使用CCI集群，在容器内部执行systemctl命令，需要以特权模式（--privileged=true）来启动容器是否支持？ 目前，CCI尚不支持特权模式。 特权容器主要场景是让容器共享、操作宿主机的设备，CCI是基于kata的hypervisor虚拟化级别隔离，所以宿主机的资源对容器完全隔离。

查看更多 →

04/Ubuntu 18.04 执行下列命令： systemctl status cloud-init systemctl status cloud-init-local systemctl status cloud-config systemctl status cloud-final

查看更多 →

执行以下命令，检查Cloud-Init开机自启动服务是否设置成功。 systemctl status cloud-init-local systemctl status cloud-init systemctl status cloud-config systemctl status cloud-final

查看更多 →

依次检查如下项： Edge-Core运行状态 systemctl status edgecore 如未启动，则启动Edge-Core systemctl start edgecore Edge-Logger运行状态 systemctl status edgelogger 如未启动，则启动Edge-Logger

查看更多 →

执行以下命令，检查Cloud-Init开机自启动服务是否设置成功。 systemctl status cloud-init-local systemctl status cloud-init systemctl status cloud-config systemctl status cloud-final

查看更多 →

off SuSEfirewall2 stop systemctl disable SuSEfirewall2_init.service systemctl disable SuSEfirewall2.service systemctl stop SuSEfirewall2_init

查看更多 →

d/rc.local systemctl start rocketmq-namesrv systemctl start rocketmq-master systemctl start rocketmq-slave 图1 设置开机自启 启动服务 重新加载systemctl配置 # systemctl

查看更多 →

执行以下命令使用networking管理网络。 systemctl disable NetworkManager systemctl disable network-manager systemctl enable networking kill `pgrep -o dhclient` systemctl stop NetworkManager

查看更多 →

如果您的集群版本在1.17.17以下，或者1.17.17以上且是隧道网络，请登录该节点，执行systemctl status canal命令查询canal服务运行状态，若回显状态异常，请执行systemctl restart canal命令后重新查询状态。 如果您的集群是1.17.17以上，且是VPC网络或云原生网络2

查看更多 →

停止IEF agent服务。 systemctl stop edgecore systemctl stop edgedaemon 更换显卡，重新安装显卡驱动，然后拷贝驱动文件，具体请参见安装并配置GPU驱动文件。 启动边缘agent服务。 systemctl start edgecore

查看更多 →

执行命令systemctl status getty@ttyS0查看getty@ttyS0是否设置为disabled，且状态为inactive。 若不是，则执行如下命令： systemctl disable getty@ttyS0-->关闭开机自启动 systemctl stop

查看更多 →

off SuSEfirewall2 stop systemctl disable SuSEfirewall2_init.service systemctl disable SuSEfirewall2.service systemctl stop SuSEfirewall2_init

查看更多 →

off SuSEfirewall2 stop systemctl disable SuSEfirewall2_init.service systemctl disable SuSEfirewall2.service systemctl stop SuSEfirewall2_init

查看更多 →

检查节点时钟同步 服务器 ntpd或chronyd是否运行正常。 解决方案 问题场景一：ntpd运行异常 请登录该节点，执行systemctl status ntpd命令查询ntpd服务运行状态。若回显状态异常，请执行systemctl restart ntpd命令后重新查询状态。 以下为正常回显： 图1 ntpd运行状态

查看更多 →

7系列/Debian/EulerOS/CentOS 7/CentOS 8系列操作系统，依次执行以下命令： systemctl disable NetworkManager.service systemctl stop NetworkManager.service 查看服务状态：service NetworkManager

查看更多 →

Run 'systemctl daemon-reload' to reload units. 如回显信息所示test1.mount磁盘发生了改变，需要运行systemctl daemon-reload重新加载units。 更改/etc/fstab时，必须执行systemctl dae

查看更多 →

off SuSEfirewall2 stop systemctl disable SuSEfirewall2_init.service systemctl disable SuSEfirewall2.service systemctl stop SuSEfirewall2_init

查看更多 →

off SuSEfirewall2 stop systemctl disable SuSEfirewall2_init.service systemctl disable SuSEfirewall2.service systemctl stop SuSEfirewall2_init

查看更多 →

-r ##加载nfs配置 #启动服务，顺序不能错 systemctl start rpcbind && systemctl enable rpcbind systemctl start nfs && systemctl enable nfs #验证 showmount -e

查看更多 →

OSOps-switch-windows-firewall.bat的执行脚本页面设置参数后，直接运行。 CentOS 7 systemctl start firewalld.service systemctl stop firewalld.service Ubuntu ufw enable ufw disable

查看更多 →

/home/ITP/share 启动NFS服务 systemctl restart rpcbind systemctl restart nfs-server（nfs） systemctl enable rpcbind systemctl enable nfs-server(nfs)

查看更多 →