Help Center/ VPC Endpoint/ Getting Started/ Configuring a VPC Endpoint for Communications Across VPCs of the Same Account/ Step 1: Create a VPC Endpoint Service
Updated on 2024-12-11 GMT+08:00
View PDF
Share

Step 1: Create a VPC Endpoint Service

Scenarios

To enable communications across two VPCs, you first need to configure a cloud resource (backend resource) in one VPC as a VPC endpoint service.

This section uses a load balancer as an example to describe how to create a VPC endpoint service.

Prerequisites

There is a load balancer in the VPC where you are going to create the VPC endpoint service.

Procedure

  1. Go to the VPC endpoint service list page.
  2. Click Create VPC Endpoint Service.

    The Create VPC Endpoint Service page is displayed.

    Figure 1 Create VPC Endpoint Service
  3. Configure required parameters.
    Table 1 Parameters for creating a VPC endpoint service

    Parameter

    Example Value

    Description

    Region

    CN-Hong Kong

    Specifies the region where the VPC endpoint service is to be deployed.

    Resources in different regions cannot communicate with each other over an intranet. For lower latency and quicker access, select the nearest region.

    Name

    -

    This parameter is optional.

    Specifies the name of the VPC endpoint service.

    The name can contain a maximum of 16 characters, including letters, digits, underscores (_), and hyphens (-).

    • If you do not enter a name, the system generates a name in {region}.{service_id} format.
    • If you enter a name, the system generates a name in {region}.{Name}.{service_id} format.

    Network Type

    IPv4

    Specifies the type of the VPC endpoint service.

    The value can be IPv4 or IPv6.

    • IPv4: Only IPv4 networks are supported.
    • IPv6: Only IPv6 networks are supported.

    VPC

    -

    Specifies the VPC where the VPC endpoint service is to be deployed.

    Subnet

    -

    Specifies the subnet where the VPC endpoint service is to be deployed.

    This parameter is mandatory when you set Network Type to IPv6.

    Service Type

    Interface

    Specifies the type of the VPC endpoint service. The type can only be Interface.

    Connection Approval

    -

    Specifies whether the connection between a VPC endpoint and a VPC endpoint service requires approval from the owner of the VPC endpoint service.

    You can enable or disable Connection Approval.

    When Connection Approval is enabled, any VPC endpoint for connecting to the VPC endpoint service needs to be approved. For details, see step 5.

    Port Mapping

    80

    Specifies the protocol and ports used for communications between the VPC endpoint service and a VPC endpoint. The protocol is TCP or UDP.

    • Service Port: provided by the backend resource bound to the VPC endpoint service.
    • Terminal Port: provided by the VPC endpoint, allowing you to access the VPC endpoint service.

    The service and terminal port numbers range from 1 to 65535. A maximum of 50 port mappings can be added at a time.

    NOTE:

    Accessing a VPC endpoint service from a VPC endpoint is to access the service port from the associated terminal port.

    If you need to run an SSH command to verify the connectivity after the configuration is complete, set Service Port to 22 according to the SSH protocol.

    Backend Resource Type

    Elastic load balancer

    Specifies the backend resource that provides services to be accessed.

    The following backend resource types are supported:

    • Elastic load balancer: Backend resources of this type suit services that receive high access traffic and demand high reliability and disaster recovery (DR) performance.
    • ECS: Backend resources of this type serve as servers.
    • BMS: Backend resources of this type serve as servers. You can choose BMS when you choose IPv4 for Network Type.
    In this example, select Elastic load balancer.
    NOTE:
    • For the security group associated with the backend resource configured for the VPC endpoint service, add an inbound rule, with Source set to 198.19.128.0/17. For details, see Adding a Security Group Rule in the Virtual Private Cloud User Guide.
    • If you configure a load balancer as the backend resource for the VPC endpoint service, and enable access control for the listener associated with the load balancer, ensure to allow traffic from 198.19.128.0/17.

    Load Balancer

    -

    When Backend Resource Type is set to Elastic load balancer, select the load balancer that provides services from the drop-down list.

    NOTE:

    If an elastic load balancer is used as the backend resource, the source IP address received by the VPC endpoint service is not the real address of the client.

    Tag

    example_key1

    example_value1

    Specifies the tag that is used to classify and identify the VPC endpoint service.

    This parameter can be modified after you create a VPC endpoint service.

    Description

    -

    Provides supplementary information about the VPC endpoint service.
    Table 2 Tag requirements for VPC endpoint services

    Parameter

    Requirement

    Tag key
    • Cannot be left blank.
    • Must be unique for each resource.
    • Can contain a maximum of 36 characters.
    • Can contain only letters, digits, hyphens (-), and underscores (_).

    Tag value
    • Cannot be left blank.
    • Can contain a maximum of 43 characters.
    • Can contain only letters, digits, hyphens (-), and underscores (_).
  4. Click Create Now.
  5. Click Back to VPC Endpoint Service List to view the newly-created VPC endpoint service.
  6. In the VPC endpoint service list, locate the VPC endpoint service and click its name to view its details.