Procedure

Prerequisites

• Cloud side
  • A VPC has been created. For details about how to create a VPC, see Creating a VPC and Subnet.
  • Security group rules have been configured for the VPC, and ECSs can communicate with other devices on the cloud. For details about how to configure security group rules, see Security Group Rules.
• Data center side
  • IPsec has been configured on the VPN device in the on-premises data center. For details, see Administrator Guide.

Procedure

Huawei Cloud VPNs support static routing mode, BGP routing mode, and policy-based mode. The following uses the static routing mode as an example.

1. Log in to the management console.
2. Click Service List and choose Networking > Virtual Private Network.
3. Configure a VPN gateway.
   1. Choose Virtual Private Network > Enterprise – VPN Gateways, and click Buy VPN Gateway.
   2. Set parameters as prompted.

      Table 1 only describes the key parameters for creating a VPN gateway.

      Table 1 Description of VPN gateway parameters

      Parameter	Description	Value
      Name	Name of a VPN gateway.	vpngw-001
      Network Type	Select Public network.	Public network
      Associate With	Select VPC.	VPC
      VPC	VPC to which the interconnection subnet belongs.	vpc-001(192.168.0.0/16)
      Interconnection Subnet	This subnet is used for communication between the VPN gateway and VPC. Ensure that the selected interconnection subnet has four or more assignable IP addresses.	192.168.2.0/24
      Local Subnet	This parameter is available only when Associate With is set to VPC. Enter CIDR block Enter the subnet that needs to access the on-premises data center. The subnet can belong to the associated VPC or not. Select subnet Select a subnet that belongs to the associated VPC and needs to access the on-premises data center.	192.168.0.0/24,192.168.1.0/24
      BGP ASN	BGP AS number.	64512
      HA Mode	Select Active-active.	Active-active
      Active EIP	Active EIP used by the VPN gateway to access the on-premises data center.	1.1.1.2
      Active EIP 2	Standby EIP used by the VPN gateway to access the on-premises data center.	2.2.2.2

4. Configure the customer gateway.
   1. Choose Virtual Private Network > Enterprise – Customer Gateways, and click Create Customer Gateway.
   2. Set parameters as prompted.

      Table 2 only describes the key parameters for creating a customer gateway.

      Table 2 Description of customer gateway parameters

      Parameter	Description	Value
      Name	Name of a customer gateway.	cgw-fw
      Routing Mode	Select Static.	Static
      Gateway IP Address	IP address used by the customer gateway to communicate with the Huawei Cloud VPN gateway. Ensure that UDP port 4500 is permitted on the customer gateway device in the on-premises data center.	1.1.1.1

5. Configure VPN connections.
   1. Choose Virtual Private Network > Enterprise – VPN Connections, and click Buy VPN Connection.
   2. Set parameters for VPN connection 1 and click Submit.

      Table 3 only describes the key parameters for creating a VPN connection.

      Table 3 Parameter settings for VPN connection 1

      Parameter	Description	Value
      Name	Name of a VPN connection.	vpn-001
      VPN Gateway	VPN gateway for which the VPN connection is created.	vpngw-001
      Gateway IP Address	Active EIP bound to the VPN gateway.	1.1.1.2
      Customer Gateway	Name of a customer gateway.	cgw-fw
      VPN Type	Select Static routing.	Static routing
      Customer Subnet	Subnet in the on-premises data center that needs to access the VPC on Huawei Cloud. A customer subnet cannot be included in any local subnet or any subnet of the VPC to which the VPN gateway is attached. Reserved VPC CIDR blocks such as 100.64.0.0/10 and 214.0.0.0/8 cannot be used as customer subnets.	172.16.0.0/16
      Interface IP Address Assignment	Manually specify In this example, select Manually specify. Automatically assign	Manually specify
      Local Tunnel Interface IP Address	Tunnel interface IP address configured on the VPN gateway.	169.254.70.1
      Customer Tunnel Interface IP Address	Tunnel interface IP address configured on the customer gateway device.	169.254.70.2
      Link Detection	Whether to enable route reachability detection in multi-link scenarios. When NQA is enabled, ICMP packets are sent for detection and your device needs to respond to these ICMP packets.	NQA enabled
      PSK, Confirm PSK	The value must be the same as the PSK configured on the customer gateway device.	Test@123
      Policy Settings	The policy settings must be the same as those on the customer gateway device.	Default

   3. Create VPN connection 2.
      

      For VPN connection 2, you are advised to use the same parameter settings as VPN connection 1, except the parameters listed in the following table.

      Table 4 Parameter settings for VPN connection 2

      Parameter	Description	Value
      Name	Name of a VPN connection.	vpn-002
      Gateway IP Address	Active EIP 2 bound to the VPN gateway.	2.2.2.2
      Local Tunnel Interface IP Address	Tunnel IP address of the VPN gateway.	169.254.71.1
      Customer Tunnel Interface IP Address	Tunnel IP address of the customer gateway.	169.254.71.2

6. Configure the customer gateway device.

   The configuration procedures may vary according to the type of the customer gateway device. For details, see Administrator Guide.

Verification

• About 5 minutes later, check states of the VPN connections.

  Choose Virtual Private Network > Enterprise – VPN Connections. The states of the two VPN connections are both Available.

• Verify that servers in the on-premises data center and ECSs in the Huawei Cloud VPC subnet can ping each other.