ALM-303046763 A VAP Fails to Be Created

Description

WLAN/4/VAP_CREATE_FAIL: OID [OID] VAP create fail.(Reason=[STRING])

A VAP fails to be created.

Attribute

Alarm ID	Alarm Severity	Alarm Type
303046763	Warning	equipmentAlarm

Parameters

Name	Meaning
Reason	Indicates the reason for the failure to create a VAP.

Impact on the System

The VAP cannot be created.

Possible Causes

**Table 1** Reasons for VAP creation failures
Reason for VAP Creation Failures	Remarks	Suggestion
The VAPs using WEP encryption on an AP cannot use the same key ID.	-	Check the configuration of the VAP profile or security profile.
Invalid WEP key index.	-	Check whether the security profile is configured correctly.
Preshared key is not configured.	-	Configure a pre-shared key.
Only one management VAP profile can be bound.	-	Delete the management VAP that has been configured.
The bridge is enabled. Please undo first.	WLAN IDs 13 and 14 are used to set up a WDS bridge. Select other WLAN IDs or delete the WDS configuration.	Select another WLAN ID or delete the WDS configuration.
WLAN ID(16) is used. Please undo first.	WLAN ID 16 is used to set up a Mesh link. Select another WLAN ID or delete the Mesh configuration.	Select another WLAN ID or delete the Mesh configuration.
Only one temporary management vap-profile can be bound to an AP.	-	Delete the offline management VAP that has been configured.
The current country code does not support 5GHz frequency band.	-	Change the country code, or do not create a 5 GHz VAP.
The current country code does not support 2.4GHz frequency band.	-	Change the country code, or do not create a 2.4 GHz VAP.
The AP type does not support the wlan id.	-	Delete unused VAPs.
This AP type does not support WDS function.	-	Replace the AP with one supporting WDS.
This AP type does not support Mesh function.	-	Replace the AP with one supporting Mesh.
This AP type or version does not support Mesh function.	-	Replace the AP with a Mesh-capable AP or upgrade the AP to a Mesh-capable version.
The number of VAPs has reached the upper limit.	-	Delete excess VAPs.
The AP does not support 5GHz frequency band.	-	Change the AP, or do not create a 5 GHz VAP.
The AP does not support 2.4GHz frequency band.	-	Change the AP, or do not create a 2.4 GHz VAP.
The AP does not support 802.1X+WEP.	-	Replace the AP with one in compliance with 802.11ac Wave 2.
SFN roaming can be configured only on one VAP of each radio.	-	Create a VAP on another radio or delete the SFN roaming VAP on the current radio.
The AP does not support SFN.	-	Replace the AP with one supporting SFN roaming.
The 5G radio of the AP does not support SFN.	-	Replace the AP or change the 5 GHz radio configuration.
The number of VAPs has reached the card specific.	-	Reduce the number of VAPs on a card, or enable the AP to go online on another card of the switch and create VAPs.
The AP in this version does not support PPSK authentication.	-	Upgrade the AP to V200R010C00 or later.
The AP in this version does not support Navi-AC VAPs.	-	Upgrade the AP to V200R010C00 or later.
Unknown reason, error code is 0x%x.	-	Contact technical support personnel.
The number of WDS VAPs has reached the upper limit.	-	Delete redundant WDS VAPs.
The number of Mesh VAPs has reached the upper limit.	-	Delete redundant Mesh VAPs.
The frequency band of this radio is inconsistent with that supported by the current country code.	-	Change the country code, or do not create a VAP for the current radio.
The AP in this version does not support the Mesh configuration on radio 2.	-	Upgrade APs to V200R020C10 or later.
The AP does not support OWE.	-	Upgrade APs to V200R020C10 or later.