Help Center/ Edge Data Center Management/ User Guide/ Getting Started/ Connecting a Device (Through the WebUI)/ Adding a Device Through Automatic Discovery
Updated on 2022-02-21 GMT+08:00
View PDF
Share

Adding a Device Through Automatic Discovery

You can add the ECC800-Pro to the smart module, AIO container, and FusionModule500 management domain through automatic discovery.

Prerequisites

  • A management domain has been created. For details, see Adding a Management Domain.
  • You have obtained device parameters.
  • The ECC800-Pro is properly connected.

Procedure

  1. Choose Device Management > Configuration > Planning Configuration.
  2. On the Planning Configuration page, click in the upper left corner.
  3. On the Uncreated Device Information page, click Access in the Operation column.
  4. In the Device Integration dialog box, set parameters for the ECC800-Pro device by referring to Figure 1, and click OK.

    You can view the task information, including Type, Device Name, Region, Progress, Status, Start Time, End Time, and Information in the displayed Progress page. You can view the operation details in Information.

    • After the management domain is successfully bound to the ECC800-Pro, all devices under the ECC800-Pro will be displayed on the Planning Configuration page and their names can be manually modified. However, devices under the ECC800-Pro cannot be moved or deleted. You can only delete all devices under the ECC800-Pro by deleting the ECC800-Pro.
    • The following lists the management domains that can be bound to different types of ECC800-Pro systems:
      • The ECC800-Pro whose system type is FusionModule500 can be bound to a FusionModule500 management domain.
      • The ECC800-Pro whose system type is FusionModule800, FusionModule2000, or FusionModule5000 can be bound to a smart module.
      • The ECC800-Pro whose system type is FusionModule1000A (the layout mode is available for the FusionModule1000A) can be bound to an AIO container.
    • After in-room monitoring is set on the ECC800-Pro, the access actuators and cameras synchronized to the NetEco will be displayed in the smart modules (smart modules created in the equipment room, outlet, subnet, or container cluster) in the same positions as where they are deployed on the ECC800-Pro. After the access actuator and camera are deleted from the ECC800-Pro, the access actuators and cameras synchronized to the NetEco are displayed only in the list of devices that are not deployed in the smart module.
    Figure 1 Adding the ECC800-Pro through automatic discovery
    • If you do not specify Authenticate Password, the site is created using the default password. If you correctly specify Authenticate Password, the site is created using the specified password.

    • During ECC800-Pro device synchronization, all opened NetEco pages are locked. In this period, you cannot perform any operations on these pages, and Loading device profile. Please try it later. is displayed. The locking duration varies. Perform operations based on the actual operation result.

    • After ECC800-Pro device synchronization, you can check or configure Management Info, Assets Info, device information, and layout information of the device in the corresponding smart module in the Planning Configuration page as required.

    • When modifying the switch states of air conditioners that use the BIN4 protocol on the Planning Configuration page, you need to enter the password on the NetEco.

Follow-up Procedure

After adding an ECC800-Pro device, you can perform operations on the device on the Planning Configuration page. The operations are as follows:

  • Modifying device parameters
    Select the added device and configure parameters in the right pane as required. Click in the upper right corner.

    Names of the devices accessed through the ECC800-Pro comply with the following rules:

    • For devices that are synchronized to the NetEco through the ECC800-Pro for the first time, if the names of the devices are not changed on the NetEco or ECC800-Pro WebUI, their default names are displayed.
    • Device names modification on the ECC800-Pro WebUI will be synchronized to the NetEco. However, device names modification on the NetEco will be synchronized to the ECC800-Pro WebUI.
  • Deleting a device

    Click a device and click Delete under to delete the device.

  • Viewing the device view

    Click the device and choose Manage under to go to the device Overview page and view the device view.