Help Center/ Direct Connect/ Best Practices/ Connecting an On-Premises Data Center to a VPC over a Single Connection and Using BGP Routing to Route Traffic

Updated on 2024-12-16 GMT+08:00

View PDF

Connecting an On-Premises Data Center to a VPC over a Single Connection and Using BGP Routing to Route Traffic

Overview

Connect your on-premises network to the cloud network and use BGP routes to route traffic between your on-premises network and the VPC.

Prerequisites

Your on-premises network must use a single-mode fiber with a 1GE, 10GE, 40GE, or 100GE optical module to connect to the access device in the cloud.
Auto-negotiation for the port must be disabled. Port speed and full-duplex mode must be manually configured.
802.1Q VLAN encapsulation is supported on your on-premises network.
On-premises devices must support BGP and cannot use ASN 64512, which is used by Huawei Cloud.

Typical Topology

Your on-premises network is connected to a VPC in the CN-Hong Kong region over a single connection.

For details on how to create a VPC, see the Creating a VPC.

The following table lists the CIDR blocks used in this example:

**Table 1** CIDR blocks
Item	CIDR Block
Your on-premises network	10.1.123.0/24
Local and remote gateways (addresses for interconnection)	10.0.0.0/30
VPC	192.168.0.0/16

Figure 1 Accessing a VPC over a connection though BGP routes
Click to enlarge

Procedure

Create a connection.

Go to the Connections page.
In the upper left corner of the page, click and select a region and project.
In the upper right corner, click Create Connection.

On the Create Connection page, enter the equipment room details and select the Direct Connect location and port based on Table 2.

Figure 2 Creating a self-service connection
Click to enlarge

**Table 2** Parameters for creating a connection
Parameter	Example Value	Description
Billing Mode	Yearly/Monthly	Specifies how you will be billed for the connection. Currently, only Yearly/Monthly is supported.
Region	CN-Hong Kong	Specifies the region where the connection resides. You can also change the region in the upper left corner of the console.
Connection Name	dc-123	Specifies the name of your connection.
Location	HK-Sai Kung-Mobile	Specifies the Direct Connect location where your leased line can be connected to.
Carrier	China Telecom	Specifies the carrier that provides the leased line.
Port Type	1GE single-mode optical port	Specifies the type of the port that the leased line is connected to. The options are as follows: 1GE, 10GE, 40GE, and 100GE.
Leased Line Bandwidth (Mbit/s)	100	Specifies the bandwidth of the line you need to lease from the carrier.
Equipment Room Address	Room xx, xx building, xx road, xx district, xx city	Specifies the address of your equipment room. The address must be specific to the floor your equipment room is on.
Tag	example_key1 example_value1	Adds tags to help you identify your connection. You can change them after the connection is created.
Description	-	Provides supplementary information about the connection.
Contact Person/Phone Number/Email	Tom +086 13912345678 (Chinese mainland) Tom@mail.com	Specifies who is responsible for your connection. CAUTION: If no contact information is provided, we will contact the person in your account information. This will prolong the review period.
Required Duration	5	Specifies how long the connection will be used for.
Auto-renew	5	Specifies whether to automatically renew the subscription to ensure service continuity. For example, if you select this option and the required duration is three months, the system automatically renews the subscription for another three months.
Enterprise Project	default	Specifies the enterprise project by which connections are centrally managed. Select an existing enterprise project.

Click Confirm Configuration.
Confirm the configuration and click Request Connection.
Then confirm the requirements with the Direct Connect manager.

If the request is not approved, repeat 1.c to 1.f based on the review comments and submit the request again.
Contact the carrier for cabling.
After the construction is complete, locate the connection in the connection list and click Confirm Cabling in the Operation column.
Figure 3 Confirm Cabling
In the displayed dialog box, click OK.
In the connection list, locate the connection and click Confirm Configuration in the Operation column.
Confirm the configuration and click Pay Now.
Confirm the order, select a payment method, and click Confirm.
Wait for Huawei Cloud to complete the construction.
Huawei onsite engineers will connect the leased line to the port on the Huawei Cloud gateway based on the customer's information within two working days.
Verify that the connection is in the Normal state, which means that the connection is ready, and the billing starts.

Create a virtual gateway.

In the navigation pane on the left, choose Direct Connect > Virtual Gateways.
Click Create Virtual Gateway.

Configure the parameters based on Table 3.

Figure 4 Creating a virtual gateway
Click to enlarge

**Table 3** Parameters required for creating a virtual gateway
Parameter	Example Value	Description
Name	vgw-123	Specifies the virtual gateway name. The name can contain 1 to 64 characters.
Enterprise Project	default	Specifies the enterprise project by which virtual gateways are centrally managed. Select an existing enterprise project.
VPC	VPC-001	Specifies the VPC to be associated with the virtual gateway.
Local Subnet	192.168.0.0/16	Specifies the CIDR blocks of the subnets in the VPC to be accessed using Direct Connect. You can add one or more CIDR blocks. If there are multiple CIDR blocks, separate every entry with a comma (,).
BGP ASN	64512	Specifies the BGP ASN of the virtual gateway. NOTE: Generally, Huawei Cloud's BGP ASN is 64512. There are two special cases: In the CN North-Beijing1 region, the default BGP ASN of Huawei Cloud is 65533. In the AP-Bangkok region, the BGP ASN of some Direct Connect locations is 65535 by default. For details, contact the Direct Connect manager.
Tag	-	Adds tags to help you identify your virtual gateway. You can change them after the virtual gateway is created.
Description	-	Provides supplementary information about the virtual gateway.

Click OK.

Create a virtual interface.

In the navigation pane on the left, choose Direct Connect > Virtual Interfaces.
In the upper right corner, click Create Virtual Interface.

Configure the parameters based on Table 4.

Figure 5 Creating a virtual interface
Click to enlarge

**Table 4** Parameters for creating a virtual interface
Parameter	Example Value	Description
Virtual Interface Owner	Current account	Specifies the account that this virtual interface will be created for.
Region	CN-Hong Kong	Specifies the region where the connection resides. You can also change the region in the upper left corner of the console.
Name	vif-test	Specifies the virtual interface name. The name can contain 1 to 64 characters.
Virtual Interface Priority	-	Specifies whether the virtual interface will be used prior to other virtual interfaces. There are two options: Preferred and Standard. If multiple virtual interfaces are associated with one Direct Connect device, the load is balanced among virtual interfaces with the same priority, while virtual interfaces with different priorities are working in active/standby pairs.
Connection	dc-test12	Specifies the connection you can use to connect your on-premises network to Huawei Cloud.
Gateway	vgw-test	Specifies the gateway that the virtual interface connects to. You can select a virtual gateway or global DC gateway. In this example, select a virtual gateway.
VLAN	30	Specifies the ID of the VLAN for the virtual interface. Standard connections: You need to configure the VLAN. Hosted connections: The VLAN will be allocated by the carrier or partner. You do not need to configure the VLAN.
Bandwidth (Mbit/s)	1000	Specifies the bandwidth that can be used by the virtual interface. The bandwidth cannot exceed that of the connection.
Enable Rate Limiting	-	Limits the highest bandwidth that can be used by the virtual interface. If this option is enabled, the rate limit gradients are as follows: If the bandwidth is less than or equal to 100 Mbit/s, the rate limit gradient is 10 Mbit/s. If the bandwidth is greater than 100 Mbit/s but is less than or equal to 1,000 Mbit/s, the rate limit gradient is 100 Mbit/s. If the bandwidth is greater than 1,000 Mbit/s but is less than or equal to 100 Gbit/s, the rate limit gradient is 1 Gbit/s. If the bandwidth is greater than 100 Gbit/s, the rate limit gradient is 10 Gbit/s. For example, if the bandwidth is 52 Mbit/s, the actual rate limit is 60 Mbit/s. If the bandwidth is 115 Mbit/s, the actual rate limit is 200 Mbit/s.
Enterprise Project	default	Specifies the enterprise project by which virtual interfaces are centrally managed. Select an existing enterprise project.
Tag	-	Adds tags to help you identify your virtual interface. You can change them after the virtual interface is created.
IP Address Family	-	Specifies the address type of the virtual interface. IPv4 is selected by default.
Local Gateway	10.0.0.1/30	Specifies the IP address used by the cloud to connect to your on-premises network. After you configure Local Gateway on the console, the configuration will be automatically delivered to the gateway used by the cloud.
Remote Gateway	10.0.0.2/30	Specifies the IP address used by the on-premises data center to connect to the cloud. After you configure Remote Gateway on the console, you need to configure the IP address on the interface of the on-premises device. CAUTION: The IP addresses of the local gateway and remote gateway must be in the same IP address range. Generally, an IP address range with a 30-bit mask is used. The IP addresses you plan cannot conflict with IP addresses used on your on-premises network. Plan an IP address range that will be used at both ends of the connection for network communication between your on-premises data center and the cloud.
Remote Subnet	10.1.123.0/24	Specifies the subnets and masks of your on-premises network. If there are multiple subnets, use commas (,) to separate them.
Routing Mode	BGP	Specifies whether static routing or dynamic routing is used to route traffic between your on-premises network and the cloud network. If there are or will be two or more connections, select BGP routing for higher availability.
BGP ASN	64510	Specifies the ASN of the BGP peer. This parameter is required when BGP routing is selected.
BGP MD5 Authentication Key	1234567	Specifies the password used to authenticate the BGP peer using MD5. This parameter can be set when BGP routing is selected, and the parameter values on both gateways must be the same. The key contains 8 to 255 characters and must contain at least two types of the following characters: Uppercase letters Lowercase letters Digits Special characters ~!,.:;-_"(){}[]/@#$%^&*+\\|=
Description	-	Provides supplementary information about the virtual interface.

Click Create Now.

The default security group rule denies all the inbound traffic. Ensure that security group rules in both directions are correctly configured to ensure normal communications.

Wait for route advertisement from the cloud.

Direct Connect automatically delivers the routes after a connection is established between your on-premises network and the cloud network.
Configure routes on your on-premises network device.

Example route (A Huawei-developed device is used an example.)
```
bgp 64510
peer 10.0.0.1 as-number 64512
peer 10.0.0.1 password simple 1234567
network 10.1.123.0 255.255.255.0
```