What Can I Do If the AS Group Fails to Be Enabled?

The possible causes and solutions are as follows:

• Issue description: Insufficient ECS, EVS disk or EIP quota.

  Possible cause: insufficient quota

  Handling method: Increase the quota or delete unnecessary resources, and then enable the AS group.

• Issue description: The VPC or subnet does not exist.

  Possible cause: The VPC service encounters an exception or resources have been deleted.

  Handling method: Wait until the VPC service recovers, or modify parameters of the VPC and subnet in the AS group, and then enable the AS group.

• Issue description: The ELB listener or backend ECS group does not exist, and the load balancer is unavailable.

  Possible cause: The ELB service encounters an exception or resources have been deleted.

  Handling method: Wait until the ELB service recovers, or modify load balance parameters in the AS group, and then enable the AS group.

• Issue description: The number of backend ECSs that you add to the ELB listener exceeds the upper limit.

  Possible cause: If classical load balancer is used by an AS group, instances added to the AS group are automatically added to the ELB listener. A maximum of 300 backend ECSs can be added to an ELB listener.

  Handling method: Remove the backend ECSs that are both not required and not in the AS group from the listener. Then enable the AS group.

• Issue description: The image used by the AS configuration, the flavor, or the key pair does not exist.

  Possible cause: Resources have been deleted.

  Handling method: Change the AS configuration for the AS group and then enable the AS group.

• Issue description: The notification subject configured for your lifecycle hook does not exist.

  Possible cause: The AS group adds a lifecycle hook, while its configured notification subject has been deleted before the scaling action starts. If the notification subject is deleted after the scaling action starts, an AS group exception will occur in the next scaling action.

  Handling method: Change the notification subject used by the lifecycle hook or delete the lifecycle hook. Then enable the AS group.

• Issue description: The subnet you select does not have enough private IP addresses.

  Possible cause: Private IP addresses in the subnet used by the AS group have been used up.

  Handling method: Modify the subnet information and enable the AS group.

• Issue description: The ECS resources of this type in the selected AZ have been sold out.

  Possible cause: ECSs of this type have been sold out or are not supported in the AZ selected for the AS group. ECSs of this type are the ECS flavor selected in the AS configuration.

  Handling method: Change the AS configuration for the AS group and then enable the AS group. If there is no instance in the AS group, you can also change the AZ for the AS group and then enable the AS group.

• Issue description: The selected specifications and the disk do not match.

  Possible cause: The ECS type in the AS configuration does not match the disk type, leading to the ECS creation failure.

  Handling method: Change the AS configuration for the AS group and then enable the AS group.

• Issue description: The selected specifications and the image do not match.

  Possible cause: The ECS type in the AS configuration does not match the image, leading to the ECS creation failure.

  Handling method: Change the AS configuration for the AS group and then enable the AS group.

• Issue description: Storage resources of this type have been sold out in the selected AZ.

  Possible cause: Storage resources of this type have been sold out or are not supported in the AZ selected for the AS group. Storage resources of this type refer to the system and data disk types selected for the AS configuration.

  Handling method: Change the AS configuration for the AS group and then enable the AS group. If there is no instance in the AS group, you can also change the AZ for the AS group and then enable the AS group.

• Issue description: The shared bandwidth defined in the AS configuration does not exist.

  Possible cause: Resources have been deleted.

  Handling method: Use a newly purchased or an existing shared bandwidth to create an AS configuration. Then change the AS configuration for the AS group and enable the AS group.

• Issue description: The number of EIPs bound to the shared bandwidth specified in the AS configuration exceeds the limit.

  Possible cause: A maximum of 20 EIPs can be bounded to a shared bandwidth.

  Handling method: Apply for a higher EIP quota, remove unnecessary EIPs from the shared bandwidth, or change another AS configuration for the AS group. Then enable the AS group.

• Issue description: The DeH selected in your AS configuration does not exist. Change the AS configuration.

  Possible cause: Resources have been deleted.

  Handling method: Use a newly purchased or an existing DeH to create an AS configuration. Then change the AS configuration for the AS group and enable the AS group.

• Issue description: No DeH is available. Ensure that there are available DeH resources.

  Handling method: Rectify the DeH fault and restore the DeH to the available state, or enable the automatic placement attribute for the DeH, and then enable the AS group again. You can also use a newly purchased DeH to create an AS configuration, change the AS configuration for the AS group, and enable the AS group.

• Issue description: The DeH selected in your AS configuration does not have sufficient capacity.

  Handling method: You can delete unnecessary ECSs from the DeH and enable the AS group again. You can also use a newly purchased DeH to create an AS configuration, change the AS configuration for the AS group, and enable the AS group.

• Issue description: No DeH is available in the AZ selected for your AS group.

  Handling method: Purchase a DeH in the AZ, use it to create an AS configuration, change the AS configuration for the AS group, and enable the AS group. If there is no instance in the AS group, change the AZ for the AS group and then enable the AS group.

• Issue description: The DeH selected in your AS configuration does not support this type of ECS. Change the AS configuration.

  Handling method: Select the ECS specifications supported by the DeH, create an AS configuration, change the AS configuration for the AS group, and then enable the AS group again.

• Issue description: A system error has occurred.

  Possible cause: An error has occurred in the AS service, peripheral service, or network.

  Handling method: Try again later or contact technical support.

• Issue description: The specification defined in the AS configuration is unavailable.

  Handling method: Change specifications by creating an AS configuration as prompted by the error message and use this AS configuration for the AS group. Then enable the AS group.

• Issue description: The selected AS configuration cannot be used by the AS group.

  Handling method: Create an AS configuration as prompted by the error message and use this AS configuration for the AS group. Then enable the AS group.

• Issue description: AS group expansion fails.

  Possible cause: Your account is in arrears or the balance is insufficient.

  Handling method: Top up your account and enable the AS group.