Buying a VPN Connection

Scenarios

To connect your on-premises data center or private network to your ECSs in a VPC, you need to create a VPN connection after a VPN gateway is obtained.

Procedure

Log in to the management console.
Click in the upper left corner and select the desired region and project.
Click Service List and choose Networking > Virtual Private Network.
In the navigation pane on the left, choose Virtual Private Network > Classic – VPN Connections.
If Enterprise Edition VPN is available for the selected region, choose Virtual Private Network > Classic.
On the VPN Connections page, click Create VPN Connection.

Configure the parameters as prompted and click Create Now. Table 1 describes the VPN connection parameters.

**Table 1** Description of VPN connection parameters
Parameter	Description	Example Value
Region	Regions are geographic areas that are physically isolated from each other. The networks inside different regions are not connected to each other, so resources cannot be shared across regions. For low network latency and fast resource access, select the region nearest to your target users.	N/A
Name	Name of a VPN connection.	vpn-001
VPN Gateway	Name of the VPN gateway for which the VPN connection is created.	vpcgw-001
Local Subnet	VPC subnets that will access your on-premises network through a VPN. You can set the local subnet using either of the following methods: Select subnet: Select the subnets that need to access your on-premises data center or private network. Specify CIDR block: Enter the CIDR blocks that need to access your on-premises data center or private network.	192.168.1.0/24, 192.168.2.0/24
Remote Gateway	The public IP address of the gateway in your data center or on the private network. This IP address is used for communicating with your VPC.	N/A
Remote Subnet	The subnets of your on-premises network that will access a VPC through a VPN. The remote and local subnets cannot overlap with each other. The remote subnet cannot overlap with CIDR blocks involved in existing VPC peering, Direct Connect, or Cloud Connect connections created for the local VPC.	192.168.3.0/24, 192.168.4.0/24
PSK	Private key shared by two ends of a VPN connection for negotiation. PSKs configured at both ends of the VPN connection must be the same. The PSK: Contains 6 to 128 characters. Can contain only: Digits Letters Special characters: ~ ` ! @ # $ % ^ ( ) - _ + = [ ] { } \| \ , . / : ;	Test@123
Confirm PSK	Enter the PSK again.	Test@123
Advanced Settings	Default: Use default IKE and IPsec policies. Existing: Use existing IKE and IPsec policies. Custom: including IKE Policy and IPsec Policy, which specifies the encryption and authentication algorithms of a VPN tunnel. For details, see Table 2 and Table 3.	Custom

**Table 2** IKE policy
Parameter	Description	Example Value
Authentication Algorithm	Hash algorithm used for authentication. The following algorithms are supported: MD5 (This algorithm is insecure. Exercise caution when using this algorithm.) SHA1 (This algorithm is insecure. Exercise caution when using this algorithm.) SHA2-256 SHA2-384 SHA2-512 The default algorithm is SHA2-256.	SHA2-256
Encryption Algorithm	Encryption algorithm. The following algorithms are supported: AES-128 AES-192 AES-256 3DES (This algorithm is insecure. Exercise caution when using this algorithm.) The default algorithm is AES-128.	AES-128
DH Algorithm	Group 1 (This algorithm is insecure. Exercise caution when using this algorithm.) Group 2 (This algorithm is insecure. Exercise caution when using this algorithm.) Group 5 (This algorithm is insecure. Exercise caution when using this algorithm.) Group 14 Group 15 Group 16 Group 19 Group 20 Group 21 The default algorithm is Group 14.	Group 14
Version	Version of the IKE protocol. The value can be one of the following: v1 (not recommended due to security risks) v2 The default value is v2.	v2
Lifetime (s)	Lifetime of an SA, in seconds An SA will be renegotiated when its lifetime expires. The default value is 86400.	86400
Negotiation Mode	The default mode is Main.	Main

**Table 3** IPsec policy
Parameter	Description	Example Value
Authentication Algorithm	Hash algorithm used for authentication. The following algorithms are supported: SHA1 (This algorithm is insecure. Exercise caution when using this algorithm.) MD5 (This algorithm is insecure. Exercise caution when using this algorithm.) SHA2-256 SHA2-384 SHA2-512 The default algorithm is SHA2-256.	SHA2-256
Encryption Algorithm	Encryption algorithm. The following algorithms are supported: AES-128 AES-192 AES-256 3DES (This algorithm is insecure. Exercise caution when using this algorithm.) The default algorithm is AES-128.	AES-128
PFS	Algorithm used by the Perfect forward secrecy (PFS) function. DH group 1 (This algorithm is insecure. Exercise caution when using this algorithm.) DH group 2 (This algorithm is insecure. Exercise caution when using this algorithm.) DH group 5 (This algorithm is insecure. Exercise caution when using this algorithm.) DH group 14 DH group 15 DH group 16 DH group 19 DH group 20 DH group 21 The default algorithm is DH group 14.	DH group 14
Transfer Protocol	Security protocol used in IPsec to transmit and encapsulate user data. The following protocols are supported: AH ESP AH-ESP The default protocol is ESP.	ESP
Lifetime (s)	Lifetime of an SA, in seconds An SA will be renegotiated when its lifetime expires. The default value is 3600.	3600

An IKE policy specifies the encryption and authentication algorithms to be used in the negotiation phase of an IPsec tunnel. An IPsec policy specifies the protocol, encryption algorithm, and authentication algorithm to be used in the data transmission phase of an IPsec tunnel. The IKE and IPsec policies must be the same at both ends of a VPN connection. If they are different, the VPN connection cannot be set up.