Adding and Editing an Incident

Scenario

This section describes how to add or edit an incident.

Adding an Incident

1. Log in to the management console.
2. Click in the upper left corner of the management console and select a region or project.
3. Click in the upper left corner of the page and choose Security & Compliance > SecMaster.
4. In the navigation pane on the left, choose Workspaces > Management. In the workspace list, click the name of the target workspace.
   Figure 1 Workspace management page
   

5. In the navigation pane on the left, choose Threats > Incidents.
   Figure 2 Incidents
   

6. On the Incidents page, click Add. On the displayed Add page, set parameters as described in Table 1.

   Table 1 Parameters for adding an incident

   Parameter		Description
   Basic Information	Incident Name	Custom incident name. The value must contain: Only uppercase letters, lowercase letters, digits, and the special characters: -_ () A maximum of 2,550 characters
   	Type	Incident type
   	(Optional) Service ID	Enter the service ID corresponding to the incident.
   	Incident Severity	Select a severity level.
   	Status	Select an incident status.
   	(Optional) Owner	Primary owner of the incident.
   	Data Source Product Name	Select the name of the data source product.
   	Data Source Type	Select the type of the data source. For example, if the data source is a cloud service, select the cloud service.
   Timeline	First Occurrence Time	Time when the incident occurred first time.
   	(Optional) Last Occurrence Time	Time when the incident occurred last time.
   	(Optional) Planned Closure Time	Time to close the incident.
   Other	(Optional) Verification Status	Verification status of the incident to identify the accuracy of the incident.
   	(Optional) Stage	Incident phase. Preparation: Prepare resources to process incidents. Detection and analysis: Detect and analyze the cause of an incident. Containment, extradition, and recovery: Handle an incident. Post Incident Activity: Follow-up activities.
   	(Optional) Debugging data	Whether to enable simulated debugging
   	(Optional) Labels	Label of the incident.
   	Description	Incident description. The value can contain: Only uppercase letters, lowercase letters, digits, and the special characters: -_ () A maximum of 10,240 characters.

7. Click OK. The incident is created.

Editing an Incident

1. Log in to the management console.
2. Click in the upper left corner of the management console and select a region or project.
3. Click in the upper left corner of the page and choose Security & Compliance > SecMaster.
4. In the navigation pane on the left, choose Workspaces > Management. In the workspace list, click the name of the target workspace.
   Figure 3 Workspace management page
   

5. In the navigation pane on the left, choose Threats > Incidents.
   Figure 4 Incidents
   

6. In the incident list, locate the row that contains the target incident and click Edit in the Operation column.
7. On the Edit page that is displayed, edit incident parameters.

   Table 2 Parameters for editing an incident

   Parameter		Description
   Basic Information	Incident Name	Custom incident name. The value must contain: Only uppercase letters, lowercase letters, digits, and the special characters: -_ () A maximum of 2,550 characters
   	Incident Type	Incident type
   	(Optional) Service ID	Enter the service ID corresponding to the incident.
   	Incident Level	Select a severity level.
   	Status	Select an incident status.
   	(Optional) Owner	Primary owner of the incident.
   	Data Source Name	Name of the data source, which cannot be changed
   	Data Source Type	Type of the data source, which cannot be changed
   Timeline	First Occurrence Time	Time when the incident occurred first time.
   	(Optional) Last Occurrence Time	Time when the incident occurred last time.
   	(Optional) Planned Closure Time	Time to close the incident.
   Other	(Optional) Verification Status	Verification status of the incident to identify the accuracy of the incident.
   	(Optional) Phase	Incident phase. Preparation: Prepare resources to process incidents. Detection and analysis: Detect and analyze the cause of an incident. Contain, extradition, and recovery: Handle an incident. Post Incident Activity: Follow-up activities.
   	(Optional) Debugging data	Whether to enable simulated debugging. This parameter cannot be modified once configured.
   	(Optional) Label	Label of the incident.
   	Description	Incident description. The value can contain: Only uppercase letters, lowercase letters, digits, and the special characters: -_ () A maximum of 10,240 characters.

8. Click OK. The incident editing is complete.