Creating an AS Group

Scenarios

An AS group consists of a collection of instances and AS policies that have similar attributes and apply to the same application scenario. An AS group is the basis for enabling or disabling AS policies and performing scaling actions. The pre-configured AS policy automatically adds or deletes instances to or from an AS group, or maintains a fixed number of instances in an AS group.

When creating an AS group, specify an AS configuration for it. Additionally, add one or more AS policies for the AS group.

Creating an AS group involves the configuration of the maximum, minimum, and expected numbers of instances and the associated load balancer.

Notes

ECS types available in different AZs may vary. When creating an AS group, choose an AS configuration that uses an ECS type available in the AZs used by the AS group.

• If the ECS type specified in the AS configuration is not available in any of the AZs used by the AS group, the following situations will occur:
  • If the AS group is disabled, it cannot be enabled again later.
  • If the AS group is enabled, its status will become abnormal when instances are added to it.
• If the ECS type specified in the AS configuration is only available in certain AZs used by the AS group, the ECS instances added by a scaling action are only deployed in the AZs where that ECS type is available. As a result, the instances in the AS group may not be evenly distributed.

Procedure

1. Log in to the management console.
2. Under Computing, click Auto Scaling.
3. Click Create AS Group.
4. Set parameters, such as Name, Max. Instances, Min. Instances, and Expected Instances. Table 1 describes the key parameters to be configured.

   Table 1 AS group parameters

   Parameter	Description	Example Value
   Region	A region is where the AS group is deployed. Resources in different regions cannot communicate with each other over internal networks. For lower network latency and faster access to your resources, select the region nearest to your target users.	N/A
   AZ	An AZ is a physical location where resources use independent power supply and networks. AZs are physically isolated but interconnected through an internal network. If you require high availability, buy servers in different AZs. If you require low network latency, buy servers in the same AZ.	N/A
   Multi-AZ Scaling Policy	This parameter can be set to Balancedor Sequenced. Balanced: When scaling out an AS group, the system preferentially distributes ECS instances evenly across AZs used by the AS group. If it fails in the target AZ, it automatically selects another AZ based on the sequenced policy. Sequenced: When scaling out an AS group, the system distributes ECS instances to the AZs according to the order in which AZs are specified. NOTE: This parameter needs to be configured when two or more AZs are selected.	Balanced
   Name	Specifies the name of the AS group to be created. The name contains 1 to 64 characters and consists of only letters, digits, underscores (_), and hyphens (-).	N/A
   Max. Instances	Specifies the maximum number of ECS instances in an AS group.	1
   Expected Instances	Specifies the expected number of ECS instances in an AS group. After an AS group is created, you can change this value, which will trigger a scaling action. The number of expected instances cannot be smaller than the minimum number of instances or greater than the maximum number of instances.	0
   Min. Instances	Specifies the minimum number of ECS instances in an AS group.	0
   AS configuration	Specifies the required AS configuration for the AS group. An AS configuration defines the specifications of the ECS instances to be added to an AS group. The specifications include the ECS image and system disk size. You need to create the required AS configuration before creating an AS group.	N/A
   VPC	Provides a network for your ECS instances. All ECS instances in the AS group are deployed in this VPC.	N/A
   Subnet	You can select up to five subnets. The AS group automatically binds all NICs to the created ECS instances. The first subnet is used by the primary NIC of an ECS instance by default, and other subnets are used by extension NICs of the instance.	N/A
   Load Balancing	This parameter is optional. A load balancer automatically distributes traffic across all instances in an AS group to balance their service load. It improves the fault tolerance of your applications and expands application service capabilities. NOTE: Up to six load balancers can be added to an AS group. After multiple load balancers are added to an AS group, multiple services can be concurrently listened to, thereby improving service scalability. If ELB health check is selected for Health Check Method, when any one of the listeners detects that an instance becomes unhealthy, AS will replace it with a new one. If you select load balancer, configure the following parameters: Load Balancer Listener	N/A
   Security Group	Controls ECS access within or between security groups by defining access rules. ECSs added to a security group are protected by the access rules you define.	N/A
   Instance Removal Policy	Controls which instances are first to be removed during scale in. If specified conditions are met, scaling actions are triggered to remove instances. You can choose from any of the following instance removal policies: Oldest instance created from oldest AS configuration: The oldest instance created from the oldest configuration is removed from the AS group first. Newest instance created from oldest AS configuration: The newest instance created from the oldest configuration is removed from the AS group first. Oldest instance: The oldest instance is removed from the AS group first. Newest instance: The latest instance is removed from the AS group first. NOTE: Manually added ECS instances are the last to be removed. If AS does remove a manually added instance, it only removes the instance from the AS group. It does not delete instance. If multiple manually added instances must be removed, AS preferentially removes the earliest-added instance first.	Oldest instance created from oldest AS configuration
   Health Check Interval	Specifies the length of time between health checks. You can set a health check interval, such as 10 seconds, 1 minute, 5 minutes, 15 minutes, 1 hour, or 3 hours, based on the service requirements.	5 minutes
   Release EIP on Instance Removal	If EIP has been selected in an AS configuration for an AS group, an EIP is automatically bound to the ECS added by a scaling action to the AS group. If you select the check box before Yes, the EIP bound to the ECS is released when the ECS is removed from the AS group. Otherwise, the system unbinds the EIP from the ECS, but does not release it when the ECS is removed from the AS group.	N/A

5. Click Next.
6. On the displayed page, you can use an existing AS configuration or create an AS configuration. For details, see Creating an AS Configuration from an Existing ECS Instance and Creating an AS Configuration from a New Specifications Template.
7. Click Next.
8. (Optional) Add an AS policy to an AS group.

   On the displayed page, click Add AS Policy.

   Configure the required parameters, such as the Policy Type, Scaling Action, and Cooldown Period. For details, see Dynamic Scaling and Scheduled Scaling.

   

   • If a scaling action is triggered by an AS policy, the cooldown period is whatever configured for that AS policy.
   • If a scaling action is triggered by manually changing the expected number of instances or by other actions, the cooldown period is whatever configured for the AS group.
9. Click Next.
10. (Optional) Configure notification for the AS group.

    For details, see Configuring Notifications for an AS Group.

11. Click Next.
12. Click Create Now.
13. Check the AS group, AS configuration, and AS policy information. Click Submit.
14. Confirm the creation result and go back to the AS Groups page as prompted.

    After the AS group is created, its status changes to Enabled.