Notes and Constraints

Quota Limits

Constraints

• Enterprise switches cannot forward unknown unicast, broadcast, and multicast (except VRRP) packets from your data center to the cloud or IPv6 packets.
• On-premises servers cannot use advanced network functions on the cloud, such as VPC Peering, Route Table, ELB, and NAT Gateway.
• If you want to use a Direct Connect connection together with an enterprise switch, submit a service ticket to check whether your connection can interconnect with an enterprise switch. If your connection does not support this, contact customer service.
• If you want to use a VPN connection together with an enterprise switch, submit a service ticket to check whether your connection supports VXLAN interconnection with an enterprise switch. If your connection does not support this, contact customer service.
• Only classic VPNs can be used together with enterprise switches.
• If cloud and on-premises networks communicate with each other at Layer 2, the cloud subnet gateway address must be the same as the on-premises subnet gateway address. Otherwise, the on-premises subnet gateway address may conflict with the IP address of a cloud server, causing communication exceptions.
• Each enterprise switch allows up to 10,000 IP addresses to communicate at Layer 2, including a maximum of 1,000 on-premises IP addresses.
• To use an enterprise switch to connect cloud and on-premises networks at Layer 2, a customer is responsible for constructing the VXLAN network of their data center equipment room, including preparing VXLAN switches, connecting physical networks, and connecting to Direct Connect or VPN.
• An enterprise switch supports MAC proxy forwarding. With ARP proxy, cloud and on-premises servers can communicate without knowing the actual MAC address of each other. The source MAC address of the packets received by the cloud server is the MAC address of the main interface of the Layer 2 connection, and the source MAC address of the packets received by the on-premises server is the MAC address of the tunnel interface. If your services need to know the actual server MAC addresses or have MAC address-based security policies, do not use an enterprise switch.
• Generally, a server determines the destination MAC address of a reply packet through ARP. However, some hosts or hardware devices (such as F5 load balancers) are configured to use the source MAC address of a request packet as the destination MAC address of its reply packet. If an enterprise switch is used for cloud and on-premises communications at Layer 3 in this case, a network disconnection may occur.

  For example, an enterprise switch allows cloud and on-premises networks to communicate on 192.168.3.0/24. If the cloud server 192.168.2.2/24 accesses the on-premises server 192.168.3.3/24, the request packet on the cloud is sent to the on-premises server through the VPC route and then the enterprise switch. The reply packet from the on-premises server is sent back to the cloud through the route and Direct Connect or VPN. If the on-premises server is configured to use the source MAC address of a request packet as the destination MAC address of its reply packet, the destination MAC address of the reply packet is not the MAC address of gateway 192.168.3.0/24, but the source MAC address of the request packet, that is, the MAC address of the enterprise switch. In this case, the destination MAC address of the reply packet is incorrect and the network is disconnected.

• If an enterprise switch uses the VXLAN protocol, the VXLAN protocol has a header of 50 bytes and the packet length increases. Your on-premises network devices that allow VXLAN packets should support jumbo frames (Ethernet frames whose MTU is greater than 1500 bytes). Otherwise, such packets cannot be transmitted.
  NOTE:

  Vendors such as Huawei, allow jumbo frames by default. However, vendors such as Cisco, do not allow jumbo frames by default.

• If you use an enterprise switch to connect your on-premises data center to the cloud, the switches of your data center must support the VXLAN function. The following lists some switches that support the VXLAN function.
  • Huawei switches: Huawei CE58, CE68, CE78, and CE88 series switches, such as CE6870, CE6875, CE6881, CE6863, and CE12800 switches
  • Switches of other vendors: Cisco Nexus 9300, Ruijie RG-S6250, and H3C S6520 series switches