Backup Import from Another Cloud Using redis-shake

Importing Backup Files

If the source Redis and the destitution Redis cannot be connected, or the source Redis is deployed on other clouds, you can migrate data by importing backup files.

1. Create a Redis Cluster instance on the DCS console.

   The memory of this instance cannot be smaller than that of the source Redis.

2. Run the following command to obtain the IP addresses and port numbers of all masters of the source Redis and target Redis:

   redis-cli -h {redis_address} -p {redis_port} -a {redis_password} cluster nodes

   In the command output similar to the following, obtain the IP addresses and ports of all masters.

   

   

   After Redis is installed, it runs with redis-cli. To install Redis on CentOS, run the yum install redis command.

3. Prepare a cloud server and install redis-shake.

   redis-shake must be able to access the target Redis and bound to an EIP.

   You can use ECS and configure the same VPC, subnet, and security group for the ECS and the DCS instance.

   Download and decompress the release version of redis-shake. (The following uses v2.1.2 as an example. You can also use other redis-shake versions.)

   

   

   If the source Redis is deployed in the data center intranet, install redis-shake on the intranet server. Export data and then upload the data to the cloud server as instructed by the following steps

4. Export the RDB file.
   • Edit the redis-shake.conf file by providing the following information about all the masters of both the source and the target:

     source.type = cluster
     # If there is no password, skip the following parameter.
     source.password_raw = {source_redis_password}
     # IP addresses and port numbers of all masters of the source Redis Cluster, which are separated by semicolons (;).
     source.address = {master1_ip}:{master1_port};{master2_ip}:{master2_port}…{masterN_ip}:{masterN_port}

   • Run the following command to export the RDB file:

     ./redis-shake -type dump -conf redis-shake.conf

     If the following information is displayed in the execution log, the backup file is exported successfully:

     execute runner[*run.CmdDump] finished!

     

     If you cannot export the source Redis backup files using this method due to cloud vendors' restrictions on the SYNC and PSYNC commands, export the files on the source console or contact the source technical support.

5. Import the RDB file.
   1. Import the RDB file (or files) to the cloud server. The cloud server must be connected to the target DCS instance.
   2. Edit the redis-shake configuration file.
      Edit the redis-shake.conf file by providing the following information about all the masters of both the source and the target:

      target.type = cluster
      # If there is no password, skip the following parameter.
      target.password_raw = {target_redis_password}
      # IP addresses and port numbers of all masters of the target instance, which are separated by semicolons (;).
      target.address = {master1_ip}:{master1_port};{master2_ip}:{master2_port}…{masterN_ip}:{masterN_port}
      # List the RDB files to be imported, separated by semicolons (;).
      rdb.input = {local_dump.0};{local_dump.1};{local_dump.2};{local_dump.3}

      Save and exit.

   3. Run the following command to import the RDB file to the target instance:

      ./redis-shake -type restore -conf redis-shake.conf

      If the following information is displayed in the execution log, the backup file is imported successfully:

      Enabled http stats, set status (incr), and wait forever.

6. Verify the migration.

   After data synchronization, access the DCS Redis Cluster instance using redis-cli. Run the info command to query the number of keys in the Keyspace section to confirm that data has been fully imported.

   If the data has not been fully imported, run the flushall or flushdb command to clear the cached data in the instance, and synchronize data again.