Help Center/ Virtual Private Cloud/ User Guide (Ankara Region)/ Route Tables/ Configuring an SNAT Server
Updated on 2024-04-15 GMT+08:00
View PDF
Share

Configuring an SNAT Server

Scenarios

Together with VPC route tables, you can configure SNAT on an ECS to enable other ECSs that have no EIPs bound in the same VPC to access the Internet through this ECS.

The configured SNAT takes effect for all subnets in a VPC.

Prerequisites

  • You have an ECS where SNAT is to be configured.
  • The ECS where SNAT is to be configured runs Linux.
  • The ECS where SNAT is to be configured has only one network interface card (NIC).

Procedure

  1. Log in to the management console.
  2. In the upper left corner of the page, click . In the service list, choose Computing > Elastic Cloud Server.
  3. On the displayed page, locate the target ECS in the ECS list and click the ECS name to switch to the page showing ECS details.
  4. On the displayed ECS details page, click the NICs tab.
  5. In the displayed area showing the NIC IP address details, disable Source/Destination Check.

    By default, the source/destination check is enabled. When this check is enabled, the system checks whether source IP addresses contained in the packets sent by ECSs are correct. If the IP addresses are incorrect, the system does not allow the ECSs to send the packets. This mechanism prevents packet spoofing, thereby improving system security. If the SNAT function is used, the SNAT server needs to forward packets. This mechanism prevents the packet sender from receiving returned packets. Therefore, you need to disable the source/destination check for SNAT servers.

  6. Bind an EIP.
  7. On the ECS console, use the remote login function to log in to the ECS where you plan to configure SNAT.
  8. Run the following command and enter the password of user root to switch to user root:

    su - root

  9. Run the following command to check whether the ECS can successfully connect to the Internet:

    Before running the command, you must disable the response iptables rule on the ECS where SNAT is configured and configure security group rules.

    ping www.google.com

    The ECS can access the Internet if the following information is displayed: 
    [root@localhost ~]# ping www.google.com
PING www.google.com (xxx.xxx.xxx.xxx) 56(84) bytes of data.
64 bytes from xxx.xxx.xxx.xxx: icmp_seq=1 ttl=51 time=9.34 ms
64 bytes from xxx.xxx.xxx.xxx: icmp_seq=2 ttl=51 time=9.11 ms
64 bytes from xxx.xxx.xxx.xxx: icmp_seq=3 ttl=51 time=8.99 ms
  10. Run the following command to check whether IP forwarding of the Linux OS is enabled:

    cat /proc/sys/net/ipv4/ip_forward

    In the command output, 1 indicates that IP forwarding is enabled, and 0 indicates that IP forwarding is disabled. The default value is 0.
    • If IP forwarding in Linux is enabled, go to step 13.
    • If IP forwarding in Linux is disabled, go to 11 to enable IP forwarding in Linux.

    Many OSs support packet routing. Before forwarding packets, OSs change source IP addresses in the packets to OS IP addresses. Therefore, the forwarded packets contain the IP address of the public sender so that the response packets can be sent back along the same path to the initial packet sender. This method is called SNAT. The OSs need to keep track of the packets where IP addresses have been changed to ensure that the destination IP addresses in the packets can be rewritten and that packets can be forwarded to the initial packet sender. To achieve these purposes, you need to enable the IP forwarding function and configure SNAT rules.

  11. Use the vi editor to open the /etc/sysctl.conf file, change the value of net.ipv4.ip_forward to 1, and enter :wq to save the change and exit.
  12. Run the following command to make the change take effect:

    sysctl -p /etc/sysctl.conf

  13. Configure the SNAT function.

    Run the following command to enable all ECSs on the network (for example, 192.168.1.0/24) to access the Internet using the SNAT function:

    iptables -t nat -A POSTROUTING -o eth0 -s subnet -j SNAT --to nat-instance-ip

    Figure 1 Configuring SNAT

    To ensure that the rule will not be lost after the restart, write the rule into the /etc/rc.local file.

    1. Switch to the /etc/sysctl.conf file:

      vi /etc/rc.local

    2. Perform 13 to configure SNAT.
    3. Save the configuration and exit:

      :wq

    4. Add the execution permissions for the rc.local file:

      # chmod +x /etc/rc.local

  14. Check whether the configuration is successful. If information similar to Figure 2 (for example, 192.168.1.0/24) is displayed, the configuration was successful.

    iptables -t nat --list

    Figure 2 Verifying configuration
  15. Add a route. For details, see section Adding a Custom Route.

    Set the destination to 0.0.0.0/0, and the next hop to the private or virtual IP address of the ECS where SNAT is deployed. For example, the next hop is 192.168.1.4.

After these operations are complete, if the network communication still fails, check your security group and network ACL configuration to see whether required traffic is allowed.

Parent topic: Route Tables