Accessing a Kafka Instance Without SASL

Prerequisites

• Security group rules have been correctly configured.

  To access a Kafka instance with SASL disabled, configure correct security group rules. For details about security group configuration requirements, see Table 2.

• The instance connection address has been obtained.
  • For intra-VPC access, use port 9092. Obtain the instance connection address in the Connection section of the Basic Information tab page.
    Figure 1 Kafka instance connection addresses for intra-VPC access without SASL
    
  • For public access, use port 9094. Obtain the instance connection address in the Connection section of the Basic Information tab page.
    Figure 2 Kafka instance connection addresses for public access without SASL
    
• If automatic topic creation is not enabled for the Kafka instance, create a topic before connecting to the instance.
• Kafka CLI v1.1.0, v2.3.0, or v2.7.2 is available. Ensure that the Kafka instance and the CLI are of the same version.
• An ECS has been created. For intra-VPC access, ensure that its VPC, subnet, and security group configurations are the same as those of the Kafka instance. JDK v1.8.111 or later has been installed on the ECS, and the JAVA_HOME and PATH environment variables have been configured as follows:

  Add the following lines to the .bash_profile file in the home directory as an authorized user: In this command, /opt/java/jdk1.8.0_151 is the JDK installation path. Change it to the path where you install JDK.

  export JAVA_HOME=/opt/java/jdk1.8.0_151 
  export PATH=$JAVA_HOME/bin:$PATH

  Run the source .bash_profile command for the modification to take effect.

Accessing the Instance Using CLI

The following uses Linux as an example.

1. Decompress the Kafka CLI package.

   Access the directory where the CLI package is stored and run the following command to decompress the package:

   tar -zxf [kafka_tar]

   In the preceding command, [kafka_tar] indicates the name of the CLI package.

   For example:

   tar -zxf kafka_2.12-2.7.2.tgz

2. Access the /bin directory of the Kafka CLI.

   In Windows, you need to access the /bin/windows directory.

3. Run the following command to create messages:

   ./kafka-console-producer.sh --broker-list ${connection-address} --topic ${topic-name}

   Parameter description:

   • {connection-address}: the address obtained in Prerequisites. For public access, use Instance Address (Public Network). For intra-VPC access, use Instance Address (Private Network).
   • {topic-name}: the name of the topic created for the Kafka instance. If automatic topic creation has enabled for the Kafka instance, set this parameter to the name of a created topic or a topic that has not been created.

   The following example uses connection addresses 10.3.196.45:9094,10.78.42.127:9094,10.4.49.103:9094. After running the preceding command, you can send a message to the Kafka instance by writing it and pressing Enter. Each line of content is sent as a message.

   [root@ecs-kafka bin]# ./kafka-console-producer.sh --broker-list 10.3.196.45:9094,10.78.42.127:9094,10.4.49.103:9094  --topic topic-demo
   >Hello
   >DMS
   >Kafka!
   >^C[root@ecs-kafka bin]# 

   To stop creating messages, press Ctrl+C to exit.

4. Run the following command to retrieve messages:

   ./kafka-console-consumer.sh --bootstrap-server ${connection-address} --topic ${topic-name} --group ${consumer-group-name} --from-beginning

   Parameter description:

   • {connection-address}: the address obtained in Prerequisites. For public access, use Instance Address (Public Network). For intra-VPC access, use Instance Address (Private Network).
   • {topic-name}: the name of the topic created for the Kafka instance
   • {consumer-group-name}: the consumer group name set based on your service requirements. If a consumer group name has been specified in the configuration file, ensure that you use the same name in the command line. Otherwise, consumption may fail. If a consumer group name starts with a special character, such as an underscore (_) or a number sign (#), the monitoring data cannot be displayed.

   Example:

   [root@ecs-kafka bin]#  ./kafka-console-consumer.sh --bootstrap-server 10.3.196.45:9094,10.78.42.127:9094,10.4.49.103:9094 --topic topic-demo --group order-test --from-beginning
   Kafka!
   DMS
   Hello
   ^CProcessed a total of 3 messages
   [root@ecs-kafka bin]# 

   To stop retrieving messages, press Ctrl+C to exit.