Updated on 2024-04-19 GMT+08:00

Creating a Shared Load Balancer

Scenarios

You have prepared everything required for creating a load balancer. For details, see Preparations for Creating a Load Balancer.

Load balancers receive requests from clients and route them to backend servers, which answer to these requests over the private network.

Constraints

  • After a load balancer is created, the VPC cannot be changed. If you want to change the VPC, create another load balancer and select the VPC during creation.
  • To ping the IP address of a load balancer, you need to add a listener and associate a backend server to it.

Procedure

  1. Log in to the management console.
  2. In the upper left corner of the page, click and select the desired region and project.
  3. Hover on in the upper left corner to display Service List and choose Network > Elastic Load Balance.
  4. On the Load Balancers page, click Buy Elastic Load Balancer. Configure the parameters based on Table 1.
    Table 1 Parameters for configuring the basic information

    Parameter

    Description

    Example Value

    Type

    Specifies the type of the load balancer.

    Shared

    Region

    Specifies the desired region. Resources in different regions cannot communicate with each other over internal networks. For lower network latency and faster access to resources, select the nearest region.

    -

  5. Configure the network parameters based on Table 2.
    Table 2 Parameters for network configurations

    Parameter

    Description

    Example Value

    Network Type

    Specifies the network type of a load balancer. You can select either of the following:

    • Public IPv4 network: The load balancer routes requests from the clients to backend servers over the Internet.
    • Private IPv4 network: The load balancer routes requests from the clients to backend servers in the same VPC as the load balancer.

    Public IPv4 network

    VPC

    Specifies the VPC where the load balancer works.

    Select an existing VPC or create one.

    For more information about VPC, see the Virtual Private Cloud User Guide.

    -

    Frontend Subnet

    Specifies the subnet where the load balancer will work.

    -

    IPv4 Address

    Specifies how you want the IPv4 address to be assigned.

    • Automatically assign IP address: The system automatically assigns an IPv4 address to the load balancer.
    • Manually specify IP address: Manually specify an IPv4 address to the load balancer.
    NOTE:

    Network ACL rules configured for the backend subnet of the load balancer will not restrict the traffic from the clients to the load balancer. If network ACL rules are configured, the clients can directly access the load balancer. To control access to the load balancer, configure access control for all listeners added to the load balancer.

    For details, see Access Control.

    Automatically assign IP address

    EIP

    Specifies the public IP address that will be bound to the load balancer for receiving and forwarding requests over the Internet.

    You can use an existing EIP or apply for a new one.

    • New EIP: The system will automatically assign an EIP.
    • Use existing: Select an existing EIP.

    New EIP

    EIP Type

    Specifies the link type (BGP) when a new EIP is used.

    • Static BGP: When changes occur on a network using static BGP, carriers cannot adjust network configurations in real time to ensure optimal user experience.
    • Dynamic BGP: When changes occur on a network using dynamic BGP, routing protocols provide automatic, real-time optimization of network configurations, ensuring network stability and optimal user experience.

    Dynamic BGP

    Billed By

    Specifies how the bandwidth will be billed.

    You can select either of the following:

    • Bandwidth: You specify the maximum bandwidth and pay for the amount of time you use the bandwidth.
    • Traffic: You specify the maximum bandwidth and pay for the total traffic you use.

    Bandwidth

    Bandwidth

    Specifies the maximum bandwidth when a new EIP is used, in Mbit/s.

    10 Mbit/s

  6. Configure other parameters about the load balancer as described in Table 3.
    Table 3 Other parameters

    Parameter

    Description

    Example Value

    Name

    Specifies the load balancer name.

    elb-test

    Enterprise Project

    Selects an enterprise project by which cloud resources and members are centrally managed.

    default

    Advanced settings

    Description

    Provides supplementary information about the load balancer.

    -

    Tag

    Identifies load balancers so that they can be easily found. A tag consists of a tag key and a tag value. The tag key marks a tag, and the tag value specifies specific tag content. For details about the naming specifications, see Table 4.

    A maximum of 10 tags can be added.

    • Key: elb_key1
    • Value: elb-01
    Table 4 Tag naming rules

    Parameter

    Requirement

    Example Value

    Tag key

    • Cannot be empty.
    • Must be unique for the same load balancer.
    • Can contain a maximum of 36 characters.
    • Only letters, digits, hyphens (-), underscores (_), and Unicode characters from \u4e00 to \u9fff are allowed.

    elb_key1

    Value

    • Can contain a maximum of 43 characters.
    • Only letters, digits, periods (.), hyphens (-), underscores (_), and Unicode characters from \u4e00 to \u9fff are allowed.

    elb-01

  7. Click Create Now.
  8. Confirm the configuration and submit your request.