Accessing a VPC over a Single Connection Through BGP Routes

Overview

Connect your on-premises network to the cloud network and use BGP routes to route traffic between your on-premises network and the VPC.

Prerequisites

• Your on-premises network must use a single-mode fiber with a 1GE, 10GE, 40GE, or 100GE optical module to connect to the access device in the cloud.
• Auto-negotiation for the port must be disabled. Port speed and full-duplex mode must be manually configured.
• 802.1Q VLAN encapsulation is supported on your on-premises network.
• Your device supports BGP and does not use ASN 64512, which is used by Huawei Cloud.

Typical Topology

Your on-premises network is connected to a VPC in the CN-Hong Kong region over a single connection.

For details on how to create a VPC, see the Creating a VPC.

The following table lists the CIDR blocks used in this example:

Table 1 CIDR blocks

Item	CIDR Block
Your on-premises network	10.1.123.0/24
Local and remote gateways (addresses for interconnection)	10.0.0.0/30
VPC	192.168.0.0/16

Figure 1 Accessing a VPC over a connection though BGP routes

Procedure

1. Create a connection.
   1. Log in to the management console.
   2. On the console homepage, click in the upper left corner and select the desired region and project.
   3. Hover on to display Service List and choose Networking > Direct Connect.
   4. In the navigation pane on the left, choose Direct Connect > Connections.
   5. Click Create Connection.
   6. On the Create Connection page, enter the equipment room details and select the Direct Connect location and port based on Table 2.
      Figure 2 Creating a self-service connection
      

      Table 2 Parameters required for creating a connection

      Parameter	Description
      Billing Mode	Specifies how you are charged for the connection. Currently, only Yearly/Monthly is supported.
      Region	Specifies the region where the connection resides. You can also change the region in the upper left corner of the console.
      Connection Name	Specifies the name of your connection.
      Location	Specifies the Direct Connect location where your leased line can be connected to.
      Carrier	Specifies the carrier that provides the leased line.
      Port Type	Specifies the type of the port that the leased line is connected to. There are four types of ports: 1GE, 10GE, 40GE, and 100GE.
      Leased Line Bandwidth	Specifies the bandwidth of the leased line in the unit of Mbit/s.
      Your Equipment Room Address	Specifies the address of your equipment room. The address must be specific to the floor your equipment room is on, for example, XX Equipment Room, XX Building, No. XX, Huajing Road, Pudong District, Shanghai.
      Tag	Identifies the connection. A tag consists of a key and a value. You can add 10 tags to a connection. Tag keys and values must meet the requirements listed in Table 3. NOTE: If a predefined tag has been created on Tag Management Service (TMS), you can directly select the corresponding tag key and value. For details about predefined tags, see Predefined Tag Overview. If you have configured tag policies for Direct Connect, you need to add tags to your connections based on the tag policies. If you add a tag that does not comply with the tag policies, connections may fail to be created. Contact the administrator to learn more about tag policies.
      Description	Provides supplementary information about the connection.
      Contact Person/Phone Number/Email	Specifies who is responsible for your connection. If you do not provide any contact information, we will contact the person in your account information.
      Required Duration	Specifies how long the connection will be used for.
      Auto-renew	Specifies whether to automatically renew the subscription to ensure service continuity. For example, if you select this option and the required duration is three months, the system automatically renews the subscription for another three months.
      Enterprise Project	Provides a cloud resource management mode where cloud resources and members are centrally managed by project.

      Table 3 Tag key and value requirements

      Parameter	Requirements
      Key	Cannot be left blank. Must be unique for each resource. Can contain a maximum of 36 characters. Can contain only letters, digits, hyphens, underscores, and Unicode characters from \u4e00 to \u9fff.
      Value	Can be left blank. Can contain a maximum of 43 characters. Can contain only letters, digits, period, hyphens, underscores, and Unicode characters from \u4e00 to \u9fff.

   7. Click Next.
   8. Confirm the connection information and click Pay Now.
   9. Confirm the order, select a payment method, and click Confirm.

2. Create a virtual gateway.
   1. In the navigation pane on the left, choose Direct Connect > Virtual Gateways.
   2. Click Create Virtual Gateway.
   3. Configure the parameters based on Table 4.
      Figure 3 Creating a virtual gateway
      

      Table 4 Parameters required for creating a virtual gateway

      Parameter	Description
      Name	Specifies the virtual gateway name. The name can contain 1 to 64 characters.
      Enterprise Project	Provides a cloud resource management mode where cloud resources and members are centrally managed by project.
      Attachment	Specifies whether the virtual gateway is associated with a VPC or attached to an enterprise router.
      VPC	Specifies the VPC to be associated with the virtual gateway. This parameter is mandatory when you set Attachment to VPC.
      Enterprise Router	Specifies the enterprise router that the virtual gateway is attached to. This parameter is displayed when you set Attachment to Enterprise Router.	N/A
      Local Subnet	Specifies the CIDR blocks of the subnets in the VPC to be accessed using Direct Connect. This parameter is mandatory when you set Attachment to VPC. You can add one or more CIDR blocks. If there are multiple CIDR blocks, separate every entry with a comma (,).
      BGP ASN	Specifies the BGP ASN of the virtual gateway. NOTE: Generally, Huawei Cloud's BGP ASN is 64512. There are two special cases: In the CN North-Beijing1 region, the default BGP ASN of Huawei Cloud is 65533. In the AP-Bangkok region, the BGP ASN of some Direct Connect locations is 65535 by default. For details, contact the Direct Connect manager.
      Description	Provides supplementary information about the virtual gateway.
      Configuration Fee	Shows the prices of the enterprise router attachment and of the traffic used by the enterprise router. This parameter is displayed when you set Attachment to Enterprise Router.

   4. Click OK.

3. Create a virtual interface.
   1. In the navigation pane on the left, choose Direct Connect > Virtual Interfaces.
   2. Click Create Virtual Interface.
   3. Configure the parameters based on Table 5.
      Figure 4 Creating a virtual interface
      

      Table 5 Parameters required for creating a virtual interface

      Parameter	Description
      Region	Specifies the region where the connection resides. You can also change the region in the upper left corner of the console.
      Name	Specifies the virtual interface name. The name can contain 1 to 64 characters.
      Virtual Interface Priority	Specifies whether the virtual interface will be used prior to other virtual interfaces. There are two options: Preferred and Standard. If multiple virtual interfaces are associated with one Direct Connect device, load is balanced among virtual interfaces with the same priority, while virtual interfaces with different priorities are working in active/standby pairs.
      Connection	Specifies the connection you can use to connect your on-premises network to Huawei Cloud.
      Virtual Gateway	Specifies the virtual gateway that the virtual interface connects to.
      VLAN	Specifies the ID of the VLAN for the virtual interface. Standard connections: You need to configure the VLAN. Hosted connections: The VLAN will be allocated by the carrier or partner. You do not need to configure the VLAN.
      Bandwidth	Specifies the bandwidth that can be used by the virtual interface, in Mbit/s. The bandwidth cannot exceed that of the connection.
      Enable Rate Limiting	Limits the highest bandwidth that can be used by the virtual interface. After this option is enabled, the rate limit gradients are as follows: If the bandwidth is less than or equal to 100 Mbit/s, the rate limit gradient is 10 Mbit/s. If the bandwidth is greater than 100 Mbit/s but is less than or equal to 1,000 Mbit/s, the rate limit gradient is 100 Mbit/s. If the bandwidth is greater than 1,000 Mbit/s but is less than or equal to 100 Gbit/s, the rate limit gradient is 1 Gbit/s. If the bandwidth is greater than 100 Gbit/s, the rate limit gradient is 10 Gbit/s. For example, if the bandwidth is 52 Mbit/s, the actual rate limit is 60 Mbit/s. If the bandwidth is 115 Mbit/s, the actual rate limit is 200 Mbit/s.
      Enterprise Project	Provides a cloud resource management mode where cloud resources and members are centrally managed by project.
      Local Gateway	Specifies the gateway on the Huawei Cloud network.
      Remote Gateway	Specifies the gateway on your on-premises network. The remote gateway must be in the same IP address range as the local gateway. Generally, a subnet with a 30-bit mask is recommended.
      Remote Subnet	Specifies the subnets and masks of your on-premises network. If there are multiple subnets, use commas (,) to separate them.
      Routing Mode	Specifies whether static routing or dynamic routing is used to route traffic between your on-premises network and the cloud network. If there are or will be two or more connections, select BGP routing to achieve higher availability.
      BGP ASN	Specifies the ASN of the BGP peer. This parameter is required when BGP routing is selected.
      BGP MD5 Authentication Key	Specifies the password used to authenticate the BGP peer using MD5. This parameter is mandatory when BGP routing is selected, and the parameter values on both gateways must be the same. The key contains 8 to 255 characters and must contain at least two types of the following characters: Uppercase letters Lowercase letters Digits Special characters ~!, .:;-_"(){}[]/@#$ %^&*+\|=
      Description	Provides supplementary information about the virtual interface.

   4. Click Create Now.
      

      The default security group rule denies all the inbound traffic. Ensure that security group rules in both directions are correctly configured for resources in the regions to ensure normal communications.

4. Wait for route propagation on the cloud.

   Direct Connect automatically propagates the routes after a connection is established between your on-premises network and the cloud network.

5. Configure a static route on your device.

   (Here is a static route on a Huawei device.)

   bgp 64510
   peer 10.0.0.1 as-number 64512
   peer 10.0.0.1 password simple 1234567
   network 10.1.123.0 255.255.255.0