Help Center/ NAT Gateway/ Getting Started/
Updated on 2024-10-12 GMT+08:00
View PDF
Share

Step 3: Buy a Public NAT Gateway

Scenarios

Buy a public NAT gateway.

Prerequisites

  • You have created the VPC and subnet required for buying a public NAT gateway.
  • To allow traffic to pass through the public NAT gateway, a route to the public NAT gateway in the VPC is required. When you buy a public NAT gateway, a default route 0.0.0.0/0 to the public NAT gateway is automatically added to the default route table of the VPC. If the default route 0.0.0.0/0 already exists in the default route table of the VPC before you buy the public NAT gateway, the default route that points to the public NAT gateway will fail to be added automatically. In this case, perform the following operations after the public NAT gateway is successfully created: Manually add a different route that points to the gateway or create a default route 0.0.0.0/0 pointing to the gateway in the new routing table.

Procedure

  1. Log in to the management console.
  2. Click in the upper left corner and select the desired region and project.
  3. Click Service List in the upper left corner. Under Networking, select NAT Gateway.

    The Public NAT Gateways page is displayed.

  4. On the displayed page, click Buy Public NAT Gateway.
  5. Configure required parameters. For details, see Table 1.
    Table 1 Descriptions of public NAT gateway parameters

    Parameter

    Description

    Billing Mode

    Public NAT gateways are billed on a pay-per-use basis.

    Region

    The region where the public NAT gateway is located

    Name

    The name of the public NAT gateway

    Enter up to 64 characters. Only digits, letters, underscores (_), and hyphens (-) are allowed.

    VPC

    The VPC that the public NAT gateway belongs to

    The selected VPC cannot be changed after you buy the public NAT gateway.

    NOTE:

    To allow traffic to pass through the public NAT gateway, a route to the public NAT gateway in the VPC is required. When you buy a public NAT gateway, a default route 0.0.0.0/0 to the public NAT gateway is automatically added to the default route table of the VPC. If the default route 0.0.0.0/0 already exists in the default route table of the VPC before you buy the public NAT gateway, the default route that points to the public NAT gateway will fail to be added automatically. In this case, perform the following operations after the public NAT gateway is successfully created: Manually add a different route that points to the gateway or create a default route 0.0.0.0/0 pointing to the gateway in the new routing table.

    Subnet

    The subnet that the public NAT gateway belongs to

    The subnet must have at least one available IP address.

    The selected subnet cannot be changed after the public NAT gateway is purchased.

    The NAT gateway will be deployed in the selected subnet. The NAT gateway works for the entire VPC where it is deployed. To enable communications over the Internet, add SNAT or DNAT rules.

    Specifications

    The specifications of the public NAT gateway

    The value can be Small, Medium, Large, or Extra-large.

    Enterprise Project

    The enterprise project that the public NAT gateway belongs to

    If an enterprise project has been configured, select the enterprise project. If you have not configured any enterprise project, select the default enterprise project.

    Description

    Supplementary information about the public NAT gateway

    Enter up to 255 characters. Angle brackets (<>) are not allowed.

    After you configure the parameters, the public NAT gateway price will be displayed. To view more pricing details, click Pricing details on the page.

  6. Click Next. On the page displayed, confirm the public NAT gateway specifications.
  7. If you do not need to modify the information, click Submit.

    It takes 1 to 5 minutes to create a public NAT gateway.

  8. In the public NAT gateway list, check the gateway status.

Adding a Default Route Pointing to the Public NAT Gateway

  1. Log in to the management console.
  2. Click in the upper left corner and select the desired region and project.
  3. Under Networking, select Virtual Private Cloud.
  4. In the navigation pane on the left, choose Route Tables.
  5. On the Route Tables page, click Create Route Table in the upper right corner.

    VPC: Select the VPC to which the public NAT gateway belongs.

    If the custom route table quota is insufficient, create a service ticket to increase the route table quota.

  6. After the custom route table is created, click its name.

    The Summary page is displayed.

  7. Click Add Route and configure parameters as follows:

    Destination: Set it to 0.0.0.0/0.

    Next Hop Type: Select NAT gateway.

    Next Hop: Select the created NAT gateway.

    Figure 1 Add Route
  8. Click OK.