Configuring VPN When Fortinet FortiGate Firewall Is Used

Scenarios

This section describes how to purchase a VPN gateway and create VPN connections on HUAWEI CLOUD to connect your on-premises network to a VPC subnet if your local data center uses FortiGate firewalls as Internet egresses.

Topology Connection

As shown in Figure 1, the local data center has multiple Internet egresses. The egress 11.11.11.11 is specified to establish a VPN connection with a VPC. The subnet of the local data center is 10.10.0.0/16, and the VPC subnet is 172.16.0.0/24. The IP address of the VPN gateway you purchased on HUAWEI CLOUD is 22.22.22.22. Create a VPN connection to connect your on-premises network to the VPC subnet.

Figure 1 Multi-egress on-premises network connecting to a VPC through a VPN

Configure the VPN connection policies on HUAWEI CLOUD based on Figure 2.

Figure 2 Policy details

Configuration Procedure

This example describes how to configure a VPN if a FortiGate firewall is used in your local data center.

1. Configure IPsec VPN.
   1. Create a tunnel.
   2. Configure the basic information for the tunnel.
   3. Configure IKE phase 1 parameters.
   4. Configure IPsec phase 2 parameters.
   5. Configure the IPsec tunnel.

2. Configure routes.
   1. Add a static route.

      Add a route to the cloud VPC subnet 172.16.0.0/24, with the outbound interface being the VPN tunnel interface.

   2. Configure policy-based routes for multiple egresses.

      Set the source address to the subnet of the local data center and the destination address to the subnet of the VPC. Adjust the configuration sequence of the policy-based routes to ensure that the policy-based routes will be preferentially used.

3. Configure policies and NAT.
   1. Configure a policy for access to the cloud from the local data center.
   2. Configure a policy for access to the local data center from the cloud.

Configuration Verification

1. Check whether the on-premises VPN status is normal.

2. Check whether the cloud-based VPN status is normal.

Configuration Using the CLI

1. Configure the physical interface.

   config system interface
      edit "port1"
           set vdom "root"
           set ip 11.11.11.11 255.255.255.0
           set type physical
   next
       edit "IPsec"                                  //Tunnel interface configuration
           set vdom "root"
           set type tunnel
           set interface "port1"               //Physical interface bound to the tunnel
                  next                    
            end

2. Configure interface zones.

   config system zone
       edit "trust"
           set intrazone allow
           set interface "A1"
       next
       edit "untrust"
           set intrazone allow
           set interface "port1 "
       next
   end

3. Configure subnets.

   config firewall address
            edit "hw-172.16.0.0/24"
           set uuid f612b4bc-5487-51e9-e755-08456712a7a0
           set subnet 172.16.0.0 255.255.255.0              //Subnet on the cloud
            next
       edit "local-10.10.0.0/16"
           set uuid 9f268868-5489-45e9-d409-5abc9a946c0c
           set subnet 10.10.0.0 255.255.0.0                     //Subnet of the local data center
       next

4. Configure IPsec.

   config vpn IPsec phase1-interface                                        //Phase 1 configuration
       edit "IPsec"
           set interface "port1"
           set nattraversal disable
           set proposal aes128-sha1
           set comments "IPsec"
           set dhgrp 5
           set remote-gw 22.22.22.22
           set psksecret ENC dmFyLzF4tRrIjV3T+lSzhQeU2nGEoYKC31NaYRWFJl8krlwNmZX5SfwUi5W5RLJqFu82VYKYsXp5+HZJ13VYY8O2Sn/vruzdLxqu84zbHEIQkTlf5n/63KEru1rRoNiHDTWfh3A3ep3fKJmxf43pQ7OD64t151ol06FMjUBLHgJ1ep9d32Q0F3f3oUxfDQs21Bi9RA==
       next
   end
   config vpn IPsec phase2-interface                                        //Phase 2 configuration
       edit "IP-TEST"
           set phase1name "IPsec "
           set proposal aes128-sha1
           set dhgrp 5
           set keylifeseconds 3600
           set src-subnet 10.10.0.0 255.255.0.0
           set dst-subnet 172.16.0.0 255.255.255.0
       next
   end

5. Configure access policies.

   config firewall policy 
    edit 15                                                  //Policy 15 is used to access the on-premises data center from the cloud. NAT is disabled.
           set uuid 4f452870-ddb2-51e5-35c9-38a987ebdb6c
           set srcintf "IPsec"
           set dstintf "trust"
           set srcaddr "hw-172.16.0.0/24"
           set dstaddr "local-10.10.0.0/16"
           set action accept
           set schedule "always"
           set service "ALL"
           set logtraffic all
       next
       edit 29                                           //Policy 29 is used to access the cloud from the on-premises data center. NAT is disabled.
           set uuid c2d0ec77-5254-51e9-80dc-2813ccf51463
           set srcintf "trust"
           set dstintf "IPsec"
           set srcaddr "local-10.10.0.0/16"
           set dstaddr "hw-172.16.0.0/24"
           set action accept
           set schedule "always"
           set service "ALL"
           set logtraffic all
       next 

6. Configure routes.

   config router static
       edit 24                                 //Route 24 is a static route that is used to access on the cloud.
           set dst 172.16.0.0 255.255.255.0
           set gateway 11.11.11.1
           set distance 10
           set device "port1"
   config router policy
   edit 2                         //Policy-based route 2 is used to access the cloud from the on-premises data center.
           set input-device "A1"
           set src "10.10.00/255.255.0.0"
           set dst "172.16.0.0/255.255.255.0"
           set gateway 11.11.11.1
           set output-device "port1"