Deze pagina is nog niet beschikbaar in uw eigen taal. We werken er hard aan om meer taalversies toe te voegen. Bedankt voor uw steun.
Direct Connect
Direct Connect
- What's New
- Function Overview
- Product Bulletin
- Service Overview
- Getting Started
- User Guide
- API Reference
-
Best Practices
- Direct Connect Best Practices
- Connecting an On-Premises Data Center to a VPC over a Single Connection and Using Static Routing to Route Traffic
- Connecting an On-Premises Data Center to a VPC over a Single Connection and Using BGP Routing to Route Traffic
- Connecting an On-Premises Data Center to a VPC over Two Connections in Load Balancing Mode (Virtual Gateway)
- Connecting an On-Premises Data Center to a VPC over Two Connections in an Active/Standby Pair (Virtual Gateway)
- Connecting an On-Premises Data Center to Multiple VPCs that Do Not Need to Communicate with Each Other
- Connecting an On-Premises Data Center to Multiple VPCs in the Same Region Using Direct Connect and VPC Peering
- Using a Public NAT Gateway and Direct Connect to Accelerate Internet Access
- Troubleshooting
-
FAQs
-
Popular Questions
- What Are the Network Requirements for Connections?
- How Do I Select a Carrier When Purchasing a Connection?
- How Will I Be Billed for Direct Connect?
- How Do I Submit a Service Ticket?
- How Do I Test the Network Connectivity Between a Location and the Cloud?
- What Do I Do If I Select the Wrong Carrier When Creating a Connection?
-
Product Consultation
- What Are the Network Requirements for Connections?
- What Are 1GE and 10GE?
- Is BGP Routing Supported in Direct Connect?
- How Do I Submit a Service Ticket?
- What Are the Network Latency and Packet Loss Rate of a Connection?
- Are the Uplink and Downlink Bandwidths of a Direct Connect Connection the Same?
- What Do I Do If I Select the Wrong Carrier When Creating a Connection?
- How Do I Plan the VPCs for a New Connection?
- What Are Local and Remote Gateways (Interconnection IP Addresses)?
- How Do I Configure BFD for a Connection?
- Leased Line
-
Interconnection with the Cloud
- Can I Access the Same VPC over Multiple Connections?
- How Do I Plan the CIDR Blocks for a Connection?
- What Should I Consider When I Use Direct Connect to Access the Cloud?
- Does Direct Connect Support NAT?
- Can the VLAN of the On-premises Network Be Used in the VPC Through Direct Connect?
- Can My On-Premises Data Center Access Multiple VPCs Through One Connection?
- Can Direct Connect Be Used with Similar Services of Other Cloud Service Providers?
-
Networking and Scenarios
- Can Multiple Connections Access the Same VPC?
- Can My On-Premises Data Center Access Multiple VPCs Through One Connection?
- Can Direct Connect Be Used with Similar Services of Other Cloud Service Providers?
- Can I Limit the Bandwidth Available on Each Hosted Connection?
- How Do I Plan the VPCs for a New Connection?
-
Related Console Operations
- How Do I Submit a Service Ticket?
- How Can I Unsubscribe from Direct Connect?
- What Parameters Can Be Modified After I Have Created a Virtual Interface?
- Do I Need to Delete the Virtual Gateway and Virtual Interface Before Deleting a Hosted Connection?
- How Do I Change the Routing Mode of a Connection?
- How Do I Delete a Hosted Connection?
- What Is the BGP ASN Used by Huawei Cloud?
- What Are Local and Remote Gateways (Interconnection IP Addresses)?
- Troubleshooting
- Billing
- Resource Monitoring
- Quota
-
Popular Questions
On this page
Show all
Help Center/
Direct Connect/
FAQs/
Billing/
Can I Unsubscribe from a Connection in the Creating State?
Can I Unsubscribe from a Connection in the Creating State?
Updated on 2024-10-23 GMT+08:00
No.
You can only unsubscribe from connections that are in the Normal state.
Parent topic: Billing
Feedback
Was this page helpful?
Provide feedbackThank you very much for your feedback. We will continue working to improve the documentation.
The system is busy. Please try again later.
