Help Center/ Direct Connect/ Best Practices/ Connecting to Multiple VPCs that Do Not Need to Communicate with Each Other
Updated on 2023-08-08 GMT+08:00

Connecting to Multiple VPCs that Do Not Need to Communicate with Each Other

Scenarios

Connect your on-premises network to two or more VPCs over one connection and use static routes to route traffic between your on-premises network and the VPCs. These VPCs do not need to communicate with each other. In this example, there are two VPCs.

Standard connections are used to provide dedicated ports for exclusive use.

Prerequisites

  • Your on-premises network must use a single-mode fiber with a 1GE, 10GE, 40GE, or 100GE optical module to connect to the access device in the cloud.
  • Auto-negotiation for the port must be disabled. Port speed and full-duplex mode must be manually configured.
  • 802.1Q VLAN encapsulation is supported on your on-premises network.

Typical Topology

Your on-premises network is connected to two VPCs over a single connection.

For details on how to create a VPC, see the Creating a VPC.

The following table lists the CIDR blocks used in this example.
Table 1 CIDR blocks

Item

CIDR Block

Your on-premises network

10.1.123.0/24

Local and remote gateways (addresses for interconnection)

10.0.0.0/30 and 10.0.0.4/30

VPCs

VPC-001: 192.168.0.0/16

VPC-002: 172.16.0.0/16

Figure 1 Accessing multiple VPCs over one connection

Procedure

  1. Create a connection.

    For details, see Accessing a VPC over a Single Connection Through Static Routes.

  2. Create two virtual gateways.

    Associate one virtual gateway with VPC-001 and the other one with VPC-002.
    Table 2 Parameters required for creating virtual gateway 1

    Parameter

    Description

    Name

    Specifies the virtual gateway name.

    The name can contain 1 to 64 characters.

    Enterprise Project

    Provides a cloud resource management mode where cloud resources and members are centrally managed by project.

    VPC

    Specifies the VPC to be associated with the virtual gateway.

    Local Subnet

    Specifies the CIDR blocks of the VPC to be accessed.

    You can add one or more CIDR blocks. If there are multiple CIDR blocks, separate every entry with a comma (,).

    Description

    Provides supplementary information about the virtual gateway.

    Table 3 Parameters required for creating virtual gateway 2

    Parameter

    Description

    Name

    Specifies the virtual gateway name.

    The name can contain 1 to 64 characters.

    Enterprise Project

    Provides a cloud resource management mode where cloud resources and members are centrally managed by project.

    VPC

    Specifies the VPC to be associated with the virtual gateway.

    Local Subnet

    Specifies the CIDR blocks of the VPC to be accessed.

    You can add one or more CIDR blocks. If there are multiple CIDR blocks, separate every entry with a comma (,).

    Description

    Provides supplementary information about the virtual gateway.

  3. Create two virtual interfaces.

    Connect each virtual interface with a virtual gateway so that your on-premises network can access VPC-001 through 10.0.0.0/30 and VPC-002 through 10.0.0.4/30.
    Table 4 Parameters required for creating virtual interface 1

    Parameter

    Description

    Region

    Specifies the region where the connection resides. You can also change the region in the upper left corner of the console.

    Name

    Specifies the virtual interface name.

    The name can contain 1 to 64 characters.

    Virtual Interface Priority

    Specifies whether the virtual interface will be used prior to other virtual interfaces. There are two options: Preferred and Standard.

    If multiple virtual interfaces are associated with one Direct Connect device, load is balanced among virtual interfaces with the same priority, while virtual interfaces with different priorities are working in active/standby pairs.

    Connection

    Specifies the connection you can use to connect your on-premises network to Huawei Cloud.

    Virtual Gateway

    Specifies the virtual gateway that the virtual interface connects to.

    VLAN

    Specifies the ID of the VLAN for the virtual interface.

    • Standard connections: You need to configure the VLAN.
    • Hosted connections: The VLAN will be allocated by the carrier or partner. You do not need to configure the VLAN.

    Bandwidth

    Specifies the bandwidth that can be used by the virtual interface, in Mbit/s. The bandwidth cannot exceed that of the connection.

    Enterprise Project

    Provides a cloud resource management mode where cloud resources and members are centrally managed by project.

    Local Gateway

    Specifies the gateway on the Huawei Cloud network.

    Remote Gateway

    Specifies the gateway on your on-premises network.

    The remote gateway must be in the same IP address range as the local gateway. Generally, a subnet with a 30-bit mask is recommended.

    Remote Subnet

    Specifies the subnets and masks of your on-premises network. If there are multiple subnets, use commas (,) to separate them.

    Routing Mode

    Specifies whether static routing or dynamic routing is used to route traffic between your on-premises network and the cloud network.

    If there are or will be two or more connections, select BGP routing to achieve higher availability.

    BGP ASN

    Specifies the ASN of the BGP peer.

    This parameter is required when BGP routing is selected.

    BGP MD5 Authentication Key

    Specifies the password used to authenticate the BGP peer using MD5.

    This parameter is mandatory when BGP routing is selected, and the parameter values on both gateways must be the same.

    The key contains 8 to 255 characters and must contain at least two types of the following characters:

    • Uppercase letters
    • Lowercase letters
    • Digits
    • Special characters ~!, .:;-_"(){}[]/@#$ %^&*+\|=

    Description

    Provides supplementary information about the virtual interface.

    Table 5 Parameters required for creating virtual interface 2

    Parameter

    Description

    Region

    Specifies the region where the connection resides. You can also change the region in the upper left corner of the console.

    Name

    Specifies the virtual interface name.

    The name can contain 1 to 64 characters.

    Virtual Interface Priority

    Specifies whether the virtual interface will be used prior to other virtual interfaces. There are two options: Preferred and Standard.

    If multiple virtual interfaces are associated with one Direct Connect device, load is balanced among virtual interfaces with the same priority, while virtual interfaces with different priorities are working in active/standby pairs.

    Connection

    Specifies the connection you can use to connect your on-premises network to Huawei Cloud.

    Virtual Gateway

    Specifies the virtual gateway that the virtual interface connects to.

    VLAN

    Specifies the ID of the VLAN for the virtual interface.

    • Standard connections: You need to configure the VLAN.
    • Hosted connections: The VLAN will be allocated by the carrier or partner. You do not need to configure the VLAN.

    Bandwidth

    Specifies the bandwidth that can be used by the virtual interface in the unit of Mbit/s. The bandwidth cannot exceed that of the connection.

    Enterprise Project

    Provides a cloud resource management mode where cloud resources and members are centrally managed by project.

    Local Gateway

    Specifies the gateway on the Huawei Cloud network.

    Remote Gateway

    Specifies the gateway on your on-premises network.

    The remote gateway must be in the same IP address range as the local gateway. Generally, a subnet with a 30-bit mask is recommended.

    Remote Subnet

    Specifies the subnets and masks of your on-premises network. If there are multiple subnets, use commas (,) to separate them.

    Routing Mode

    Specifies whether static routing or dynamic routing is used to route traffic between your on-premises network and the cloud network.

    If there are or will be two or more connections, select BGP routing to achieve higher availability.

    BGP ASN

    Specifies the ASN of the BGP peer.

    This parameter is required when BGP routing is selected.

    BGP MD5 Authentication Key

    Specifies the password used to authenticate the BGP peer using MD5.

    This parameter is mandatory when BGP routing is selected, and the parameter values on both gateways must be the same.

    The key contains 8 to 255 characters and must contain at least two types of the following characters:

    • Uppercase letters
    • Lowercase letters
    • Digits
    • Special characters ~!, .:;-_"(){}[]/@#$ %^&*+\|=

    Description

    Provides supplementary information about the virtual interface.

    The default security group rule denies all the inbound traffic. Ensure that security group rules in both directions are correctly configured to ensure normal communications.

  4. Wait for route propagation on the cloud.

    Direct Connect automatically propagates the routes after a connection is established between your on-premises network and the cloud network.

  5. Configure a static route on your device.

    (Here is a static route on a Huawei device.)

    ip route-static 192.168.0.0 255.255.0.0 10.0.0.1
    ip route-static 172.16.0.0 255.255.0.0 10.0.0.5